Set the environment variable 'fdtfile' depending on ENET workaround
detection.
The function tqma6_get_fdt_configuration is implemented to be reusable
for configuration detection in multi-DTB FIT image and therefore returns
the devicetree name without the '.dtb' ending.
Set fdtfile only if CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG is enabled and it
is currently unset.
The model string is loaded from the device tree variant. Therefore, the
overriding of the model string is being removed.
Signed-off-by: Paul Gerber <Paul.Gerber@tq-group.com>
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
TQMa6 SOM beginning with hardware rev. 0200 comes in two flavours:
With and without a hardware workaround for ENET errata err006687.
Therefore we need two flavours of device tree. To be able to detect
the presence of the workaround we need to check GPIO1_6 is connected
to I2C bus or not. If the I2C bus is detected, the workaround is not
used and separate I2C buses are used for the SoM and the baseboard.
Later on this detection will be used to select the correct devicetree
at runtime.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Add boot phase properties from U-Boot device tree.
This commit can be reverted if changes are integrated in upstreem
device trees and synced with U-Boot.
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
We will need GPIO to distinguish between SOM variants with / without
workaround for ENET errata. This is necessary to implement the
appropriate solution and remove code intended for the non-DM use case.
To support reuse, split them in SOM and baseboard specific parts.
Prepare fragments for use with SPL.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Add simple driver for i.MX SNVS RTC IP present in NXP i.MX SoCs.
Signed-off-by: Alexander Koch <akoch@initse.com>
Signed-off-by: Marek Vasut <marex@nabladev.com>
Handle both MMC2 and SD2 boot devices as SDMMC device 1 on
Data Modul i.MX8M Mini eDM SBC. In case the system boots from
a microSD card, the BootROM reports boot device as SD2_BOOT
instead of MMC2_BOOT. Continue booting from that SDMMC device
instead of falling back to SDP. Note that SDMMC device 1 is
the microSD slot on this device, SDMMC device 2 is the eMMC,
but BootROM reports the numbers the other way around, hence
the potential confusion in this commit message.
Fixes: 0b97a394f6 ("ARM: imx: Replace YModem with SDP on Data Modul i.MX8M Mini eDM SBC SPL")
Signed-off-by: Marek Vasut <marex@nabladev.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add the new 0242 PID4 to config block handling:
- 0242 Verdin AM62 Dual 1GB WB ET
Update the board-specific variant selection to use the Wi-Fi variant
for the new WB SKU.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Add the new 0239 PID4 to config block handling:
- 0239 Verdin iMX8M Mini Quad 2GB WB IT
Update the board-specific variant selection to use the Wi-Fi variant
for the new WB SKU.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Add the new Verdin iMX8M Plus 64GB eMMC PID4s to config block handling:
- 0236 Verdin iMX8M Plus Quad 4GB WB IT
- 0237 Verdin iMX8M Plus Quad 4GB IT
- 0238 Verdin iMX8M Plus Quad 8GB WB IT
Update the board-specific variant selection to use the Wi-Fi variant for
the new WB SKUs.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Use alias-based RAM probing to detect different memory configurations
on Toradex Aquila iMX95. The address wrap-around is not linear: address
bits above the module capacity alias back with some low address bits
XORed (bit 32 -> XOR 0xc000), as measured on 4GB and 8GB modules.
During probing, skip the first 256MB, since that region is reserved.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Use alias-based RAM probing to detect different memory configurations
on Toradex SMARC iMX95. The address wrap-around is not linear: address
bits above the module capacity alias back with some low address bits
XORed (bit 32 -> XOR 0xc000), as measured on 4GB and 8GB modules.
During probing, skip the first 256MB, since that region is reserved.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Add missing firmware/optee node, so is can be both used and copied into
Linux device tree by optee_copy_firmware_node(). This is consistent with
other i.MX93 boards.
Signed-off-by: Mathieu Dubois-Briand <mathieu.dubois-briand@bootlin.com>
The FSPI header is now generated purely using binman, drop no longer
supported nxp,fspi-header-filename property.
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@nabladev.com>
The FSPI header is now generated purely using binman, drop no longer
supported nxp,fspi-header-filename property.
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@nabladev.com>
Stop depending on the current mkimage method of generating the FSPI
header, instead generate the FSPI header within binman itself. This
is more flexible, as the FSPI header properties can be configured
from within the board-specific DT instead of being hard-coded in
mkimage at build time.
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@nabladev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
errloc stores bit positions of errors returned by decode_bch().
The maximum number of correctable errors is ecc_bits, so errloc
must have ecc_bits entries. The array was allocated with data_length
entries instead, which is the number of EEPROM data bytes -- orders
of magnitude larger than needed and incorrect.
Fixes: b418dfe16e ("board: ge: make VPD code common")
Signed-off-by: Md Shofiqul Islam <shofiqtest@gmail.com>
Select TQ_COMMON_SYSINFO to use the tq_eeprom sysinfo driver
to read and print module EEPROM data.
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
TQMa6UL has board-information located in EEPROM at offset 0x20.
Add necessary nodes and properties for nvmem-cells.
Revert this commit once the upstream linux device trees are
accepted and synchronized.
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Since b57ed14793 ("dts: imx8m{m,n,p,q}: Make optee packaging optional")
the TEE node is always present in U-Boot proper fitImage, even if the
CONFIG_OPTEE is disabled because the u-boot.itb should not contain any
tee.bin. This is wasteful, and produces the following warning which is
also confusing to users:
"
Image 'image' is missing optional external blobs but is still functional: tee-os
/binman/section/fit/images/tee/tee-os (tee.bin):
See the documentation for your board. You may need to build Open Portable
Trusted Execution Environment (OP-TEE) and build with TEE=/path/to/tee.bin
"
Reinstate the CONFIG_OPTEE ifdeffery to mitigate the problem, but retain the
binman "optional" keyword at tee.bin .
Before:
"
$ mkimage -l u-boot.itb
FIT description: Configuration to load ATF before U-Boot
Created: Tue Jun 30 17:23:54 2026
Image 0 (uboot)
...
Image 2 (tee) <------------------------------ bogus empty image entry
Description: OP-TEE |
Created: Tue Jun 30 17:23:54 2026 |
Type: Trusted Execution Environment Image |
Compression: uncompressed |
Data Size: 0 Bytes = 0.00 KiB = 0.00 MiB <--------'
Image 3 (fdt-1)
...
"
After:
"
$ mkimage -l u-boot.itb
FIT description: Configuration to load ATF before U-Boot
Created: Tue Jun 30 17:58:15 2026
Image 0 (uboot)
...
Image 1 (atf)
...
Image 2 (fdt-1)
...
"
Fixes: b57ed14793 ("dts: imx8m{m,n,p,q}: Make optee packaging optional")
Signed-off-by: Marek Vasut <marex@nabladev.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The current DRAM calibration sequence is implemented based on NXP
AN4467 Rev.2 03/2015, which in chapter "12.3.2 Calibration Sequence
Setup with Predefined Data Content" states:
"
9. For each of the DQSx:
- Read the HW_DG_UPx value from the MMDC0/1_MPDGHWSTx, subtract the
value of 0xc0 (3/4 cycle).
"
However, the i.MX 6Solo/6DualLite Applications Processor Reference
Manual, Rev. 5, 05/2020, chapter "45.11.3.1.2 Hardware DQS Calibration
with pre-defined value" states:
"
35. Set (MPDGHWSTn[HW_DG_UPn][10:7] - 1) to MPDGCTRLn[DG_HC_DELn].
(We set the DQS gating value to be the upper limit value minus
1 half cycle)
"
The i.MX 6Dual/6Quad Applications Processor Reference Manual, Rev. 6,
05/2020, chapter 44.11.3.1.2 Hardware DQS Calibration with pre-defined
value lists the same information. So do the following manuals:
- i.MX 6DualPlus/6QuadPlus Applications Processor Reference Manual, Rev. 3, 05/2020
chapter 46.11.3.1.2 Hardware DQS Calibration with pre-defined value
- i.MX 6SoloX Applications Processor Reference Manual, Rev. 4, 05/2020
chapter 40.11.3.1.2 Hardware DQS Calibration with pre-defined value
- i.MX 6UltraLite Applications Processor Reference Manual, Rev. 2, 03/2017
chapter 33.11.3.1.2 Hardware DQS Calibration with pre-defined value
- i.MX 6ULL Applications Processor Reference Manual, Rev. 1, 11/2017
chapter 35.11.3.1.2 Hardware DQS Calibration with pre-defined value
- i.MX 6ULZ Applications Processor Reference Manual, Rev. 0, 10/2018
chapter 29.11.3.1.2 Hardware DQS Calibration with pre-defined value
The NXP MMDC DDR Stress Test (3.0.0) tool seems to be have the same
way as the later document rather than the AN4467 application note,
and produces values similar to the values with subtracted 1/2 cycle.
Adjust the behavior to match the more recent Reference Manual and
the MMDC calibration tool.
Winbond W634GU6RB does show sporadic signs of instability without
this correction.
Signed-off-by: Marek Vasut <marex@nabladev.com>
Tested-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Because the i2c address of some gpio expander devices are same, so
in dts they have same node name which lead to same gpio device name.
Users can't get the GPIO through GPIO API or GPIO command.
Add the label to each gpio expander node, hence give unique name.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Check the GPIO2 dts node status to determine reset it or not.
On iMX952 single SPL/U-Boot image is shared for both mx952evk
and mx952evkrpmsg SM configs. GPIO2 is assigned to M7 domain
in mx952evkrpmsg, and there is no active user of GPIO2 for
mx952evk and mx952evkrpmsg in SPL/U-Boot, so it is disabled in
DTS. Otherwise, reset GPIO2 will meet hang when working with
mx952evkrpmsg SM.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When working with SM config mx9{4,5,52}evkrpmsg, mcores are not booted
by ROM. Hence, power on the mcore and initialize TCM ECC in u-boot for
subsequent mcore booting.
Signed-off-by: Ye Li <ye.li@nxp.com>
[fabio: Adapted to mainline context]
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Support booting CM70, CM71 and CM33 sync core image by bootaux command
on iMX95, iMX94 and iMX952. (iMX95 and iMX952 only supports CM70).
Each core uses different core id which is defined by SM and passed in
SIP call.
- CM33: 0
- CM70: 1
- CM71: 7
- CM33S: 8
Prior to run bootaux to start core, prepaux is needed before loading
image. Below is example for booting CM70 TCM image on iMX95.
=>fatload mmc 1:1 0x90000000 rpmsg.bin
=>prepaux 1
=>cp.b 0x90000000 0x203c0000 ${filesize}
=>bootaux 0 1
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Add new command bootaux_cntr to replace bootaux in secure boot
(CONFIG_AHAB_BOOT=y) to authenticate signed M33 core image.
The M33 image must be packed in container format and signed.
bootaux_cntr supports Mcore image loaded to TCM or run as
FlexSPI NOR XIP.
Signed-off-by: Ye Li <ye.li@nxp.com>
[fabio: Adapted to use gd->dram[i]]
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Although it has similar naming the Librem 5 Devkit is a completely
different design from the Librem 5 phone. It uses an imx8mq SOM from
Emcraft, a separate HDMI port instead of DisplayPort, different USB-C
chip, panel, etc.
This is based on a Emcraft's SOM documentation, Purism's downstream fork
and the available schematics of the devkit.
Link: https://developer.puri.sm/Librem5/Development_Environment/Boards/imx8.html
Link: https://source.puri.sm/Librem5/dvk-mx8m-bsb
Co-authored-by: Angus Ainslie <angus@akkea.ca>
Co-authored-by: Manuel Traut <manut@mecka.net>
Signed-off-by: Manuel Traut <manut@mecka.net>
Tested-by: Manuel Traut <manut@mecka.net>
Signed-off-by: Guido Günther <agx@sigxcpu.org>
[fabio: Removed the arch/arm/dts/Makefile entry that does not apply and
it is not needed as the board uses OF_UPSTREAM]
Signed-off-by: Fabio Estevam <festevam@gmail.com>
With CONFIG_FIT_BEST_MATCH, fit_conf_find_compat() selects the
configuration matching the most specific U-Boot compatible string; on
equal matches the first listed configuration wins and the configurations
node 'default' property is never consulted.
A FIT whose configurations all share the same base devicetree compatible
(e.g. one manifest carrying a base tree plus overlay combinations for a
single board) therefore always boots the first configuration, silently
ignoring the default chosen by the manifest author.
Break score ties in favour of the default configuration. A strictly
better compatible match still wins over it, and FITs without a default
keep the current first-listed behaviour.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
We have a new mailing list but the old one still forwards to the new
one, although some people (including me) have issues with the forward
and their mails to the old mailing list being dropped due to SPF policy.
Add an entry in .mailmap so that Cc: u-boot@lists.denx.de in "old"
cover letters and patches use the new mailing list address.
Tested with b4 ty --dry-run on a series from the old mailing list.
Tested with a Cc: u-boot@lists.denx.de in a commit log with b4 (b4
send), git-format-patch and git-send-email somehow don't seem to be
respecting this mapping. At least one tool (the one we now recommend)
does the right thing, so it's progress :)
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
DCACHE_OFF is defined as (0 << 2) = 0, and PTE_TYPE_FAULT is defined
as (0 << 0) = 0. In mmu_set_region_dcache_behaviour(), the cache
attribute passed to set_regions() is computed as:
attrs = PMD_ATTRINDX(option >> 2)
For DCACHE_OFF=0 this evaluates to PMD_ATTRINDX(0) = 0, which equals
PTE_TYPE_FAULT.
Commit 6468ca13ff ("armv8: mmu: fix and optimise explicitly unmapping
regions") added an unmap path to set_one_region() that
triggers when attrs == PTE_TYPE_FAULT. Because DCACHE_OFF and
PTE_TYPE_FAULT share the same numerical value (0), any call to
mmu_set_region_dcache_behaviour() with DCACHE_OFF silently unmaps the
target region instead of changing its cache attributes to non-cached.
The subsequent flush_dcache_range() call at the end of
mmu_set_region_dcache_behaviour() then crashes with a Level 3
translation fault because the region it tries to flush has just been
unmapped.
The existing flag parameter already distinguishes the two callers:
- mmu_set_region_dcache_behaviour() always passes flag=false
- mmu_change_region_attr_nobreak() always passes flag=true, and is the
only legitimate caller that passes PTE_TYPE_FAULT to unmap a region
Guard the unmap path with flag so that DCACHE_OFF attribute changes
take the correct else branch, which ORs in the ATTRINDX bits only,
leaving the PTE valid.
This was observed as a boot crash on Versal, Versal Net, and ZynqMP
platforms during network initialisation. The zynq_gem driver calls
mmu_set_region_dcache_behaviour() with DCACHE_OFF to make its BD
descriptor ring non-cached. With the bug the BD memory is unmapped,
and the subsequent dcache flush inside
mmu_set_region_dcache_behaviour() faults.
Fixes: 6468ca13ff ("armv8: mmu: fix and optimise explicitly unmapping regions")
Signed-off-by: Akshay Belsare <akshay.belsare@amd.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add a driver model serial driver for Espressif ESP32 UART
controllers. The driver supports ESP32, ESP32-S3 and ESP32-S31 UART
register variants, including baud-rate setup, FIFO access and basic
port initialization.
Signed-off-by: Honbo He <hehongbo918@gmail.com>
Changes in v3:
- Add debug UART for early print output
For a compressed kernel_noload image, bootm_load_os() allocates a
per-image decompression buffer of ALIGN(image_len * 8, SZ_1M) rather
than the global CONFIG_SYS_BOOTM_LEN. When decompression fails on that
path, handle_decomp_error() still prints
Image too large: increase CONFIG_SYS_BOOTM_LEN
which is misleading: increasing CONFIG_SYS_BOOTM_LEN does not help
because the smaller per-image buffer is the actual bound. Commit
2ff26c1e378d ("bootm: fix overflow of the noload kernel decompression
buffer") worked around this by printing a follow-up note right after
handle_decomp_error() returned, but the boot log then reads as two
contradictory sentences.
Introduce enum bootm_decomp_limit and pass it into
handle_decomp_error() so the helper picks the right message in one
place. For the per-image path it now prints
Image too large for the per-image decompression buffer (0x100000 bytes)
quoting the actual buffer size; the global path is unchanged. Drop the
trailing note in bootm_load_os() so only one line is printed.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Aristo Chen <aristo.chen@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
found_key() is declared to return bool but returns NULL when strdup()
fails. NULL is a pointer constant; while it happens to convert to
zero (i.e. false) it is a type mismatch that trips stricter
compilers/static analysers.
Return false to match the declared return type.
Signed-off-by: Naveen Kumar Chaudhary <naveen.osdev@gmail.com>
pstore_save() writes four different filenames into a fixed 256-byte
stack buffer 'path' using sprintf() with "%s" fed from argv[3] (the
user-supplied mount directory). The U-Boot command line buffer
(CONFIG_SYS_CBSIZE) is typically 1024 or 2048 bytes, so a directory
path in argv[3] can easily exceed 240 characters and overflow 'path',
corrupting the surrounding stack frame including the return address.
Replace the four sprintf(path, ...) call sites with snprintf() using
sizeof(path) as the bound. The neighbouring sprintf() calls into the
'addr' and 'length' buffers are left as-is; they write fixed-width
numeric conversions whose maximum length is bounded by the size of
ulong/u32 in hex and cannot overflow those buffers.
Signed-off-by: Naveen Kumar Chaudhary <naveen.osdev@gmail.com>
The help text advertises "<addr> [byte count]" but do_strings()
stores argv[2] directly into last_addr and the loop condition tests
"addr < last_addr", i.e. it treats the value as an absolute end
address. When invoked as documented (e.g. "strings 0x40000000
0x100") the loop condition fails immediately because the supplied
count is far below start_addr, and the command prints nothing.
Compute last_addr as start_addr + hextoul(argv[2], NULL) so the
argument is used as a length in bytes, matching the help. The
existing repeat-mode fixup (last_addr = addr + (last_addr -
start_addr)) continues to preserve the same byte-count window
across CMD_FLAG_REPEAT.
Signed-off-by: Naveen Kumar Chaudhary <naveen.osdev@gmail.com>
In case dm_rtc_reset() returns -ENOSYS, it means the .reset callback
in RTC driver is not implemented, likely because the callback is not
needed. Handle the -ENOSYS return code as success and proceed, else
the 'date reset' invocation incorrectly prints a bogus warning:
"## Failed to set date after RTC reset".
Signed-off-by: Marek Vasut <marex@nabladev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Aristo Chen <aristo.chen@canonical.com> says:
fit_import_data() in tools/fit_image.c declares the data pointer and
the name of the external data property outside its loop over the
/images subnodes, so both values leak from one image into the next. An
image node that carries data-size but neither data-offset nor
data-position then reuses the pointer left behind by the previously
imported image: the previous image's data is written into the node,
after which the import aborts trying to delete an external data
property the node never had. Since that abort path only prints a
debug() message, a regular mkimage build fails with nothing but the
generic usage text. The failure mode also depends on the order of the
image nodes: when no externally stored image precedes the malformed
node, the pointer is still NULL, the node is skipped, and the hashing
stage reports a proper error instead.
A FIT authored from a .its cannot hit this, because dtc-authored
images carry inline data. It takes re-processing an external-data FIT
in which an image has lost its data-offset, for example one edited
with fdtput -d or produced by another tool:
mkimage -E -f demo.its demo.itb
fdtput -d demo.itb /images/kernel-2 data-offset
mkimage -F demo.itb
There is no silent-success path, because the failing property delete
always aborts the run before the file is written back, but the user is
left without any indication of what is wrong.
Patch 1 moves the declarations into the loop so that each image starts
from a clean state. A node without an external data reference is now
skipped consistently regardless of node order, and the later
processing stages report the malformed node with a proper error
message (Can't get image data/size).
Patch 2 adds a regression test that builds an external-data FIT,
deletes the data-offset property of the second image and re-processes
the result with mkimage -F. It asserts that mkimage fails and that the
diagnostic is present on stderr; the unfixed tool fails the second
assertion since it prints nothing beyond the usage text.
Link: https://lore.kernel.org/r/20260710153343.1839357-1-aristo.chen@canonical.com
Build an external-data FIT, remove the data-offset property from the
second image so that only its data-size remains, and re-process the
result with mkimage -F. mkimage must reject the malformed FIT with a
clear diagnostic from the hashing stage. Previously the stale per-image
state in fit_import_data() made the import copy the first image's data
into the second image and abort without printing anything.
Signed-off-by: Aristo Chen <aristo.chen@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The data pointer and the name of the external data property are
declared outside the loop over the image nodes, so their values leak
from one image into the next. An image node that carries data-size but
neither data-offset nor data-position then reuses the pointer of the
previously imported image: the previous image's data is written into
the node before the import aborts when it tries to delete an external
data property the node does not have. Since that abort path only prints
a debug message, mkimage fails without any indication of what is wrong.
The failure mode also depends on the order of the image nodes: when no
externally stored image precedes the malformed node, the stale pointer
is still NULL, so the import skips the node and the hashing stage
reports a proper error instead.
Move the declarations into the loop so that each image starts from a
clean state. A node without an external data reference is now skipped
consistently regardless of node order, and a malformed node is always
reported by the later processing stages with a proper error message.
Signed-off-by: Aristo Chen <aristo.chen@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fixes:
* Fixed some wrong parents of VLP clocks on mt8189.
* Added a missing perficfg_ao clock in mt8188.
* Disabled watchdog by default on Genio 510/700.
* Fixed U-Boot DT overrides not included on Genio 510/700.
Cleanups/refactoring:
* Changed how clock parent providers are registered and looked
up for all MediaTek targets.
* Removed duplicate devicetree node in mt7623.
* Removed unused/non-standard DT properties in mt798{1,6,8}.
* Simplified MAINTAINERS by using N: instead of F: when possible.
* Replaced duplicate driver names in all MediaTek clock drivers.
* Cleaned up MediaTek power domain driver and split into separate
driver per compatible target.
* Removed unused power domain enablement from mt798{1,6,6a,7,8}.
Features:
* Added power domain driver for mt8188.
