ifdef CONFIG_CPU only works in U-Boot proper but macro is not working when
XPL phases are used. In this case CONFIG_SPL_CPU is also defined and can be
disabled which is causing compilation error.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
In commit 6e4675b8e5 ("lmb: replace the lmb_alloc() and
lmb_alloc_base() API's") an additional allocation was mistakenly
introduced resulting in ${kernel_comp_size} containing the address of a
second 64mb region rather than the actual value of KERNEL_COMP_SIZE.
Additionally, in commit b40d7b8f72 ("Merge patch series "lmb: use
a single API for all allocations"") merge conflict resulted in an
additional 128mb allocation for ${loadaddr} when CONFIG_FASTBOOT
is enabled, where it should actually be set to the same value as
${fastboot_addr_r} to respect size constraints (and since it doesn't
seem to interfer with any bootflows).
Fixup both of these, freeing up 192mb of memory.
Fixes: 6e4675b8e5 ("lmb: replace the lmb_alloc() and lmb_alloc_base() API's")
Fixes: b40d7b8f72 ("Merge patch series "lmb: use a single API for all allocations"")
Link: https://lore.kernel.org/r/20250811104710.1896382-1-casey.connolly@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>
These changes are mostly smaller fixes, and some additions that were
dependent on recent DT updates: We switch the S3/V3/V3s over to
OF_UPSTREAM, the DTs were already identical anyway. While at it, Paul
sent more fixes for this SoC, I am pulling in two easy fixes that were
ready and low risk. Apart from other assorted fixes, this PR also
enables Ethernet on the new A527/T527 boards, made possible by the DT
update from the DT rebasing repository.
This passed the CI, and was boot tested on boards with Allwinner A10,
A20, A33, V40, A80, A83T, T113s3, F1C100s, H3, A64, H6, H616, A133 and
T527 SoCs.
The JEDEC LPDDR3 spec defines mode register 0 (MR0) as being read-only,
so there is no point in trying to set its value.
Also the H616 memory controller encodes the mode register index to be
written starting from bit 8 in MRCTRL1 (for LPDDR3 and LPDDR4 chips), so
we need to OR in that number to tell the controller which MR to program.
On top of that, the mode registers between DDR3 and LPDDR3 are
completely different, so writing values crafted for DDR3 into a LPDDR3
chip is just wrong. Due to the above mentioned bugs the writes for
MR0-MR2 did not have any effect (as they were all trying to set the
read-only MR0), so the mode registers just stayed unchanged.
Looking at the LPDDR3 spec and the BSP code, let's write the proper MR
values into LPDDR3 chips, using the proper addressing mode.
Use the opportunity to document the LPDDR3 mode register bits written.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
58e9502e6 "arm: sunxi: Enable SPL/SPI boot for Olinuxino Lime2-eMMC
boards" enabled SPI boot for the eMMC variant. Olimex offers the
"s16MB" variant with SPI flash populated but without eMMC populated.
Tested on board rev L.
Signed-off-by: Eric Anderson <ejona86@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Recent changes in the H6 clock code added delay() calls into the SPL clock
setup routine, which requires the timers to work. When compiling for
AArch64, we are always using the Arm Generic Timer (aka. arch timer),
which does not require further setup, hence having an empty timer_init()
routine.
However for 32-bit SoCs we use the Allwinner timers, which require some
setup routine, and hence we need timer_init() to be called before
clock_init().
Swap the order of the two calls, to be more robust when compiling the H6
clock code for AArch32 or when using the Allwinner timers for whatever
reason.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The pinecube has an ethernet connector which uses the EMAC and internal
PHY of the chip. Enable it in the config.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Variables holding addresses are typically using the "long" C type in
U-Boot, to be easily compatible with both 32-bit and 64-bit builds.
The A133 DRAM driver is typically compiled for AArch64, so u64 is the
same type as unsigned long, but that breaks when compiling the DRAM
driver in AArch32 (for some experiments).
Fix the type to make the code more portable.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The first of the two Ethernet controllers in the Allwinner A527/T527 is
compatible to the MAC from the previous SoCs. Consequently the recent DT
update brought use the MAC node, using the A64 compatible string as the
fallback, which works out of the box.
Enable the sun8i-emac Ethernet driver in the defconfig for the Radxa and
the Avaota boards, so that kernels and other data can be loaded via
TFTP. Please note that only one of the Ethernet sockets will work, the
second MAC is not compatible, and needs a new U-Boot driver. The
X96QPro+ TV box unfortunately uses only this second EMAC, so Ethernet
cannot be used there at the moment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The name of the pin function was changed last minute in the DT, from
emac0 to gmac0.
Adjust the name we use in the pinctrl driver accordingly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The V3s (using co-packaged DRAM) runs at 360 MHz, which is specified in
the common platform Kconfig file. However the value for MACH_SUN8I will
be picked up instead due to ordering.
Re-order the defaults to have MACH_SUN8I_V3S before MACH_SUN8I and let
it select the correct default. Also update the LicheePi Zero Dock
defconfig to remove the value, which is now correctly selected.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
There is nothing special for u-boot in the V3/V3s device-tree files,
they are just copies of the upstream ones.
Remove the copies and switch to OF_UPSTREAM for supported boards.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
In order to set the BOOTFILE symbol we first need to have USE_BOOTFILE
be set, or some of the logic might not work as expected later on when
building. Second, defaults like this belong with the symbol itself.
Fixes: da595d236b ("include: configs: soc64: Use CONFIG_SPL_ATF to differentiate bootfile")
Signed-off-by: Tom Rini <trini@konsulko.com>
This pull request introduces initial U-Boot support for Agilex7 M-series, along
with several enhancements and cleanups across existing Agilex platforms. Key
changes include new board support, DDR driver additions, updated device trees,
and broader SoCFPGA SPL improvements.
Highlights:
- Agilex7 M-series bring-up:
- Basic DT support and board initialization for Agilex7 M-series SoC and
SoCDK.
- New sdram_agilex7m DDR driver with UIBSSM mailbox support and HBM support.
- Clock driver support for Agilex7 M-series.
- New defconfig: socfpga_agilex7m_defconfig.
- Agilex and Agilex5 enhancements:
- Improved SPL support: ASYNC interrupt enabling, system manager init
refactor, and cold scratch register usage.
- Updated firewall probing and watchdog support in SPL.
- Cleaned up DDR code, added secure region support for ATF, and improved warm
reset handling.
- Device Tree and config updates:
- Migration to upstream Linux DT layout for Agilex platforms.
- Consolidated socfpga_agilex_defconfig and removed deprecated configs.
- Platform-specific environment variables for Distro Boot added.
- Driver fixes and cleanups:
- dwc_eth_xgmac and clk-agilex cleanup and improvements.
- Several coverity and style fixes.
Contributions in this PR are from Alif Zakuan Yuslaimi, Tingting Meng, and
Andrew Goodbody. This patch set has been tested on Agilex 5 devkit, Agilex
devkit and Agilex7m devkit.
Passing all pipeline tests at SoCFPGA U-boot custodian
https://source.denx.de/u-boot/custodians/u-boot-socfpga/-/pipelines/27318
Pull request efi-2025-10-rc2
Documentation:
* Describe running U-Boot as a pflash image on RISC-V QEMU
* Correct the description of the bootph-verify device-tree property
UEFI:
* In mkeficapsule fix a resource leak in read_bin_file()
* Support loading a Linux initial RAM disk with the bootefi command.
use the new email address for community work.
While at it, cleanup git shortlog output, by adding
fixes in .mailmap
Signed-off-by: Heiko Schocher <hs@nabladev.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/27314
- Several Smatch reported fixes.
- Enable the temperature command on imx8ulp-evk.
- Fix mx8mm_fracpll_tbl.
- Make optee packaging optional for imx8m.
- Reuse and export low_drive_freq_update() on imx9.
- Enable USB OTG ID pin pull up in SPL on dh-imx6.
This is for new platform enablement for Agilex7 M-series.
Add DDR driver for Agilex7 M-series. This driver is designed to support
DDR and HBM memory. The official HBM handoff is not ready yet, therefore
hardcoded handoff is used for HBM driver validation on mUDV board.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Add uibssm mailbox driver for Agilex7 M-series. HPS will interact with UIB
and HBM subsystem through software defined mailbox interface.
HPS can retrieve HBM memory interface calibration status, UIB
configuration, memory interfae configuration, trigger calibration and etc
with the list of supported mailbox command type and opcode.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
ATF boot flow (SPL->ATF->U-Boot Proper->OS) boot to OS via kernel.itb file
using bootm command.
Change to use CONFIG_SPL_ATF to differentiate the bootfile of default
environment variable. We shouldn't use CONFIG_FIT because it is enabled
by default for U-Boot Proper.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Agilex7 M-series support has been added using upstream Linux DTS.
socfpga_agilex_socdk-u-boot.dtsi was updated to support both Agilex and
Agilex7 M-series platforms.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Migrate the legacy Agilex platform to use the upstream Linux device tree
configuration. This helps reduce maintenance overhead and aligns U-Boot
with the Linux kernel's DTS hierarchy and naming conventions.
This change improves consistency between U-Boot and Linux by removing
custom/legacy DTS handling and instead relying on the standardized
definitions provided by the upstream Linux DTS.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Reorganize misplaced properties by moving board-common settings from
socfpga_agilex_socdk-u-boot.dtsi to socfpga_agilex-u-boot.dtsi to maintain
proper separation between common and board-level configurations.
Signed-off-by: Tingting Meng <tingting.meng@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
SPL checks for a magic word in the system manager's scratch
register to determine if an L2 reset has occurred. If detected,
SPL places all slave CPUs (CPU1–3) into WFI mode. The master
CPU (CPU0) then initiates a warm reset by writing to the RMR_EL3
system register and also enters WFI mode.
This warm reset flow is handled entirely within the HPS. The
function `socfpga_sysreset_request()` triggers the warm
reset, and upon SPL re-entry, the updated `lowlevel_init_soc64.S`
handles the necessary initialization.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Put all slave CPUs (CPU1-3) into WFI mode. Master CPU (CPU0) writes
the magic word into system manager's scratch register to indicate
the system has performed L2 reset and request reset manager to
perform hardware handshake and then trigger L2 reset. CPU0 put
itself into WFI mode. L2 reset will reboot all HPS CPU cores after
which all HPS cores are in WFI mode. L2 reset is followed by warm
reset request by SPL via RMR_EL3 system register.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Agilex retrieves its clock manager address via probing its own clock
driver model during the SPL initialization.
Therefore, excluding Agilex from calling its clock driver in misc
driver to retrieve the clock manager address.
Once all SoC64 devices has been successfully transition to clock
driver model method, this implementation will be cleaned up.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
The DDR data rate must be set correctly in the DDRIOCTRL
register according to the Actual Clock Frequency (ACF) value.
By enabling the reading of ACF value from bit 18 of the boot
scratch register during initialization, the DDR data rate is
able to be configured accurately.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
The boot scratch cold reg 8 is shared between DBE, DDR init progress
update and Linux EDAC. This patch defines how the bits are used by
respective features above and their macro names used in U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@altera.com>
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
Setting up firewall regions based on SDRAM memory banks configuration
(up to CONFIG_NR_DRAM_BANKS banks) instead of using whole address space.
First 1 MiB (0 to 0xfffff) of SDRAM is configured as secure region,
other address spaces are non-secure regions. The ARM Trusted Firmware (ATF)
image is located in this first 1 MiB memory region. So, this can prevent
software executing at non-secure state EL0-EL2 and non-secure masters
access to secure region.
Add common function for firewall setup and reuse for all SoC64 devices.
Signed-off-by: Alif Zakuan Yuslaimi <alif.zakuan.yuslaimi@altera.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@altera.com>
