Use dev_remap_addr_index() which supports both live device tree and flat DT
backends, avoiding direct dependency on devfdt_* helpers.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add armada-8040-nbx-u-boot.dtsi with the firmware/optee node guarded
by CONFIG_OPTEE. This allows U-Boot to probe the OP-TEE driver only
when OP-TEE support is enabled in the configuration.
Signed-off-by: Vincent Jardin <vjardin@free.fr>
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
Read device identification data from a dedicated eMMC region. This
provides:
- Unique device serial number for identification and tracking
- Factory-programmed MAC address for network interfaces
- Bundle information for device variant identification
The serial structure includes CRC32 validation to detect corruption.
On read failure or invalid data, sensible defaults are used to ensure
the system remains bootable.
The fbxserial command provides two subcommands:
- fbxserial show: Display serial info (default)
- fbxserial init: Initialize ethaddr from serial info
Use CONFIG_PREBOOT="fbxserial init" to automatically set MAC addresses
during boot. This approach avoids patching shared board code.
Signed-off-by: Vincent Jardin <vjardin@free.fr>
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
Add the emmcboot command as board-specific support for the Nodebox 10G.
This is a legacy boot format that has been in production on this board
for many years so it cannot change anymore. It implements a dual-bank
boot system for reliable firmware updates:
- Bank0: Stable/fallback boot image
- Bank1: Newer/test boot image with reboot tracking
The boot order depends on the nrboot counter stored in eMMC:
- Healthy state (counter < 4): Try Bank1 first, then Bank0
- Degraded state (counter >= 4): Try Bank0 first, then Bank1
Each bank stores an image tag with CRC32 validation. The counter uses
a bit-counting scheme for wear leveling and tracks consecutive failed
boots to trigger automatic fallback.
Signed-off-by: Vincent Jardin <vjardin@free.fr>
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
Add board support for the Freebox Nodebox 10G based on the Marvell
Armada 8040 SoC. This board features:
- Quad-core ARMv8 AP806 with dual CP110 companions
- eMMC storage via Xenon SDHCI controller
- 1G SGMII Ethernet on CP0 lane 5
- I2C buses for peripheral access
- NS16550 UART console at 115200 baud
The implementation includes:
- Device tree for the Nodebox 10G hardware
- Dedicated board directory (board/freebox/nbx10g/)
- Board-specific Kconfig and defconfig
The U-Boot comphy bindings (phy-type/phy-speed) differ from the
mainline Linux PHY framework bindings used by phy-mvebu-cp110-comphy,
so U-Boot and the kernel each have their own device tree.
Signed-off-by: Vincent Jardin <vjardin@free.fr>
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
Add CPU information display for Armada 8040 platforms.
The soc_info.c reads the AP806 Sample-At-Reset (SAR) register to
determine the PLL clock configuration and converts it to actual
CPU, DDR, and Fabric frequencies using the PLL frequency table.
Signed-off-by: Vincent Jardin <vjardin@free.fr>
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
Set the ops structure as static const. The structure is not accessible
from outside of this driver and is not going to be modified at runtime.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
All of these platforms enable CONFIG_BOARD_EARLY_INIT_F and then have a
do-nothing board_early_init_f function. Change to not enabling the
option and so not needing an empty function.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
CONFIG_SYS_IS_IN_ENV does not exist.
CONFIG_SYS_CONSOLE_IS_IN_ENV seems to be needed here.
Fixes: f1054661e5 ("serial: serial_octeon_bootcmd.c: Add PCI remote console support")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
Due to this, legacy.c was neither compiled nor linked into the binary
and thus booting legacy DS414 firmware failed. Missing atag setup led to
no console output (and probably stalled boot) after:
| Uncompressing Linux... done, booting the kernel.
Fixes: 9774462e34 ("arm: Disable ATAGs support")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Some boards building this source define CFG_SYS_TCLK as a term involving
readl() which is undefined otherwise.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Add the Allied Telesis x220 board. There are a number of other variants
with the same CPU block that are sold under some different brand names
but the x220 was first.
The x220 uses the AlleyCat3 switch chip with integrated ARMv7 CPU.
Because of this it is reliant on a binary blob for the DDR training. In
upstream u-boot this is replaced by an empty file.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
nand-keep-config is used to retain the NAND controller configuration
from an earlier boot stage. In U-Boot's case there isn't an earlier boot
stage so reconfiguring the NAND controller is required.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
info->controller.active is not initialised so the dev_err() call ends up
dereferencing a null pointer causing a crash instead of outputting the
error. Add a dev member to struct pxa3xx_nand_info and use that instead
of info->controller.active->mtd.dev.
Fixes: 661c98121d ("mtd: nand: pxa3xx: Fix not calling dev_xxx with a device")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <stefan.roese@mailbox.org>
Fix two NULL pointer dereferences in mvpp2_phy_connect():
1. port->phy_dev->dev is used in dev_warn() but
port->phy_dev is not assigned yet (assigned later at line below).
2. port->phy_dev->dev is used in dev_err() inside
the "if (!phy_dev)" block, which means phy_dev is NULL.
Both cases would cause a crash if the PHY detection fails or returns
a generic PHY. Use the already available 'dev' parameter instead.
Fixes: 9db60ee470 ("net: mvpp2: Convert netdev_xxx to dev_xxx")
Signed-off-by: Vincent Jardin <vjardin@free.fr>
These assorted patch series from Peng Fan (OSS) <peng.fan@oss.nxp.com>
have the goal to remove the direct usage of devfdt_ APIs in drivers. The
device APIs supports both live device tree and flat DT backends,
avoiding direct dependency on devfdt_* helpers.
Use dev_read_addr_index() which supports both live device tree and flat DT
backends, avoiding direct dependency on devfdt_* helpers.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use dev_remap_addr_index() instead of devfdt_remap_addr_index() to map the
controller registers, removing the dependency on FDT-specific helpers.
Replace the direct fdt_get_property() lookup combined with dev_of_offset()
by dev_read_prop().
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use dev_remap_addr() which supports both live device tree and flat DT
backends, avoiding direct dependency on devfdt_* helpers.
And only mapping sizeof(void *) is wrong, RNG_FIFO_COUNT_OFFSET(0x24) is
accessed in this driver. So dev_remap_addr() could also fix the mapping
size.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use dev_read_addr_index() which supports both live device tree and flat DT
backends, avoiding direct dependency on devfdt_* helpers.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use dev_read_addr_index() which supports both live device tree and flat DT
backends, avoiding direct dependency on devfdt_* helpers.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use dev_read_addr_ptr() which supports both live device tree and flat DT
backends, avoiding direct dependency on devfdt_* helpers.
While at here, correct error return value, when priv->scu is NULL,
PTR_ERR(priv->scu) is 0 which implies success. Change to return '-EINVAL'.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use dev_read_addr_ptr() and dev_read_addr_index_ptr() which support both
live device tree and flat DT backends, avoiding direct dependency on
devfdt_* helpers.
While at here, also use ofnode_read_s32_default() to replace
fdtdec_get_int().
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use dev_read_addr_size_name_ptr() which supports both live device tree and
flat DT backends, avoiding direct dependency on devfdt_* helpers.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Use dev_read_addr_x() which supports both live device tree and flat DT
backends, avoiding direct dependency on devfdt_* helpers.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use dev_read_addr_x() which supports both live device tree and flat DT
backends, avoiding direct dependency on devfdt_* helpers.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use dev_read_addr_size_index() which supports both live device tree and
flat DT backends, avoiding direct dependency on devfdt_* helpers.
While at here, drop unused 'node'.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use dev_read_addr_ptr() which supports both live device tree and flat DT
backends, avoiding direct dependency on devfdt_* helpers.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use dev_remap_addr() to simplify code.
dev_remap_addr() does same thing as dev_read_addr() + map_physmem(). And
it supports both live device tree and flat DT backends, avoiding direct
dependency on devfdt_* helpers.
Also add error handling logic.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use dev_read_addr() which supports both live device tree and flat DT
backends, avoiding direct dependency on devfdt_* helpers.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use dev_read_addr_index() which supports both live device tree and flat
DT backends, avoiding direct dependency on devfdt_* helpers.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Replace devfdt_get_addr_ptr() with dev_read_addr_ptr() when retrieving the
register base address.
dev_read_addr_ptr() supports both live device tree and flat DT backends,
avoiding direct dependency on devfdt_* helpers.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Replace devfdt_get_addr_index_ptr() with dev_read_addr_index_ptr() when
retrieving the register base address.
dev_read_addr_index_ptr() supports both live device tree and flat DT
backends, avoiding direct dependency on devfdt_* helpers.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Replace devfdt_get_addr_ptr() with dev_read_addr_ptr() when retrieving the
register base address.
dev_read_addr_ptr() supports both live device tree and flat DT backends,
avoiding direct dependency on devfdt_* helpers.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Replace devfdt_get_addr_ptr() with dev_read_addr_ptr() when retrieving the
register base address.
dev_read_addr_ptr() supports both live device tree and flat DT backends,
avoiding direct dependency on devfdt_* helpers.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Replace devfdt_get_addr_ptr() with dev_read_addr_ptr() when retrieving the
register base address.
dev_read_addr_ptr() supports both live device tree and flat DT backends,
avoiding direct dependency on devfdt_* helpers.
No functional changes.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Julien StephanandDavid Lechner
Tom Rini
Peng FanandStefan Roese
Vincent JardinandStefan Roese
Marek VasutandStefan Roese
Heinrich SchuchardtandStefan Roese
Phil SutterandStefan Roese
Chris PackhamandStefan Roese
Tony DinhandStefan Roese