Ensure ROCKCHIP_DEVICE_SETTINGS is defined before including
rk3588_common.h in board include/configs files.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Ensure ROCKCHIP_DEVICE_SETTINGS is defined before including
rk3568_common.h in board include/configs files.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The partitions env variable is using an outdated partition layout that
is typically expected to be used with older vendor miniloader blobs.
Rockchip devices will run fine using any partition layout if the first
16 MiB of MMC storage is ignored/skipped.
Remove the partitions env variable to stop encourage users a continued
use of this outdated partition layout on RK3588 devices.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The partitions env variable is using an outdated partition layout that
is typically expected to be used with older vendor miniloader blobs.
Rockchip devices will run fine using any partition layout if the first
16 MiB of MMC storage is ignored/skipped.
Remove the partitions env variable to stop encourage users a continued
use of this outdated partition layout on RK356x devices.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Define constants for hptimer reg names and use them instead of magic
numbers in rockchip_stimer_init().
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip RK3576 SoC uses a different DRAM base address, 0x40000000,
compared to prior SoCs.
Add default options that should work when 0x40000000 is used as DRAM
base address. Use same offsets as before, just below 64 MiB.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
New Rockchip SoCs will typically require use or an external TPL when
support for the SoC is added to U-Boot.
Move imply ROCKCHIP_EXTERNAL_TPL under SoC Kconfig symbol to remove a
future likelihood of a long "default y if" line.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The ROCKCHIP_COMMON_STACK_ADDR Kconfig option was originally enabled
in the SoC specific Kconfig files to ease during the initial migration
to use common stack addresses.
All boards for the affected SoCs have been migrated to use common stack
addresses. Migrate to use an imply under the SoC symbol instead of
re-define the symbol in each SoC specific Kconfig file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A few Rockchip ARMv7 SoCs use 0x60000000 as DRAM base address instead of
the more common 0x0 DRAM base address used on AArch64 SoCs.
Add default options that should work for these ARMv7 SoCs. Same offsets
as before are used, just below 64 MiB. Hex values have also been padded
to improve alignment.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The stack-pointer addresses used with ROCKCHIP_COMMON_STACK_ADDR expect
that DRAM is initialized by TPL or ROCKCHIP_EXTERNAL_TPL, that SPL has
access to full DRAM and SPL is loaded to/executed from start of DRAM.
Add depends on to ensure use of the ROCKCHIP_COMMON_STACK_ADDR symbol
does not cause problem for any board not using TPL and back-to-BROM
loading of SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Kconfig symbol ROCKCHIP_COMMON_STACK_ADDR currently imply the
TPL_ROCKCHIP_COMMON_BOARD option when TPL=y. This is inconvenient for a
SoC with very limited SRAM to use a custom tpl.c together with the
common stack addresses.
Move any imply TPL_ROCKCHIP_COMMON_BOARD to under the SoC symbol, where
it belongs. Add the missing imply to RK3328 and PX30 use a SoC specific
tpl.c and only expect imply TPL_LIBGENERIC_SUPPORT.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Haikou carrierboard allows multiple adapter boards to be connected, for
now there exists the following adapter boards compatible with PX30
Ringneck:
- Haikou Video Demo on the Video Connector,
- Haikou LVDS 9904379 on the Video Connector,
So support DT overlays so we can use this mechanism instead of full DTB
containing both the carrierboard and the adapter.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to be able to use Device Tree Overlays, the fdtoverlay_addr_r
needs to be specified.
Follow what's been done for other Rockchip SoCs and leave 1MiB for the
base DTB before the address for the overlay.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
I don't see a reason why this should only be enabled on a per-board
basis. The rng IP is inside the SoC and doesn't seem to rely on anything
external to it, therefore let's enable it on the SoC DTSI and remove the
now empty px30-evb-u-boot.dtsi.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The build system uses HAVE_VENDOR_COMMON_LIB to automatically include
board/$(VENDOR)/common/Makefile, therefore let's use that to implicitly
include board/theobroma-systems/common/Makefile and compile the common.c
file when building proper.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Nothing is calling the function rk_board_init() and the io-domain driver
can handle the functions intended purpose based on information from DT.
Cleanup by removing the unused rk_board_init() function and re-sort
included headers.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The default value of 0x800000 (8 MB) is somewhat limiting for us, as our
compressed kernel may grow up to around 4 MB. By choosing the commonly
used value of 0x2000000 (32 MB), we are definitely on the safe side.
This rather large amount should be fine, as we have 128 MB of RAM.
Signed-off-by: Ezra Buehler <ezra.buehler@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Jiaxun Yang <jiaxun.yang@flygoat.com> says:
This is a huge series which promoted MIPS/Boston target into a
usable state, with fixes to drivers and general framework issues
I found in this process.
I also converted the target to OF_UPSTREAM.
This target is covered by QEMU, to test on QEMU:
```
make boston64r6el_defconfig
make
qemu-system-mips64el -M boston -cpu I6500 -bios ./u-boot.bin -nographic
```
Link: https://lore.kernel.org/r/20240517-boston-v3-0-1ea7d23f4a1d@flygoat.com
Paul had left MIPS a couple of years ago, his email address is
no longer valid.
Replace it with his kenrel.org email, which has been used in
kernel and QEMU, in case we still want to reach him.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
In upstream devicetree, clk_boston is a child of syscon node
and there is no "regmap" property for clk_boston node.
Try to check parent device first to look for syscon.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Provide default environment variables on image loading address
to make the board useful.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This is a PC-like platform board.
Enable drivers for most on-board devices to make it useful.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Remove hard dependencies to arch headers, get clock from clk
subsystem if arch clock function is not available, align
compatible strings with devicetree binding.
No functional change on existing platforms, just get it build
on other platforms.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Ensure that we are using correct physical/virtual address for
DMA buffer write and hardware register settings.
The convention is: in ahci_ioports all pointers are virtual,
that will be converted to physical address when writing to
hardware registers or into sg/cmd_tbl.
Also fixed 64bit physical address support for dwc_ahsata, ensure
higher bits are written into registers/sg properly.
Use memalign for allocating aligned buffer in dwc_ahsata so we
don't have to do our own alignment in driver.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
For MIPS we are always looking gd->dram in virtual address so
PCI_MAP_SYSTEM_MEMORY should always be enabled.
If in future we ever want to make it physical we have to set
ARCH_MAP_SYSMEM.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Boston has a very limited memory range for PCI controllers, where
1MB can't easily fit into it.
Make alignment boundary of PCI memory resource allocation a Kconfig
option and default to 0x10000 for boston.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Probe size of ecam from devicetree properly and cap accessible
bus number accorading to ecam region size to ensure we don't go
beyond hardware address space.
Also disable all interrupts to ensure errors are handled silently.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Jerome Forissier <jerome.forissier@linaro.org> says:
There is a bug in the print_guid() unit test in test/common/print.c when
PARTITION_TYPE_GUID is not enabled but either CMD_EFIDEBUG or EFI are.
The first patch fixes the issue and the second one enables UNIT_TEST in
the qemu_arm64 defconfig so that the unit tests are run in CI (this
platform has CMD_EFIDEBUG so the bug applies).
Link: https://lore.kernel.org/r/20250416074839.1267396-1-jerome.forissier@linaro.org
The name defined for PARTITION_SYSTEM_GUID in list_guid[] depends on
configuration options. It is "system" if CONFIG_PARTITION_TYPE_GUID is
enabled or "System Partition" if CONFIG_CMD_EFIDEBUG or CONFIG_EFI are
enabled. In addition, the unit test in test/common/print.c is incorrect
because it expects only "system" (or a hex GUID).
Make things more consistent by using a clear and unique name: "EFI
System Partition" whatever the configuration, and update the unit test
accordingly.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add the follow board to VIRT which otherwise would be unmaintained:
* qemu-riscv64_smode_acpi_defconfig
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add the following boards to VIRT which otherwise would be unmaintained.
* qemu_arm64_acpi_defconfig
* qemu_arm64_lwip_defconfig
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The qemu* "generic" targets (i.e. not those emulating a particular
board) are typically used for testing as many features as possible,
especially in CI so it makes sense to have UNIT_TEST enabled for
all of the defconfigs for these targets.
Not enabling UNIT_TEST in qemu-x86_defconfig due to:
LD u-boot
ld.bfd: section .rel.dyn VMA wraps around address space
ld.bfd: section .start16 LMA [fffff800,fffff86f] overlaps section .rel.dyn LMA [ffffb77c,0002ac93]
make: *** [Makefile:1824: u-boot] Error 1
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Some test commands (such as "false", or the empty string) need
CONFIG_HUSH_PARSER=y. Fix test/cmd/command.c.
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
i2c updates for v2025.07-rc1
- omap24xx_i2c: Enable Repeated Start functionality
add Repeated Start functionality for the DM_I2C xfer
API (omap_i2c_xfer()
from Aniket Limaye
- mediatek i2c driver
fixes from Martin
- add end marker for struct udevice_id mtk_i2c_ids
- remove duplicate entry in mt_i2c_regs_v1
This pull request contains updates for the SoCFPGA platform, targeting
the 2025.07 release cycle. Highlights include enhancements to Agilex5
support, improvements in DDR error handling, and bridge reset handling
for SoC64 devices.
Key updates:
Agilex5 platform enhancements:
* New MMU region mappings and memory layout updates using
LMB_ARCH_MEM_MAP.
* Fixes for bloblist configuration, kernel FIT image generation, and
VAB flow enablement.
* GPIO pin control added for SDIO selection.
* Marvell PHY driver enabled in defconfig.
Agilex5 / SoC64 DDR subsystem:
* Added ECC debug improvements for IOSSM.
* Introduced LPDDR inline ECC support.
* Resolved size calculation overflow in memory driver.
SoC64 improvements:
* Enhanced mailbox communication with the SDM to reflect various
boot stage transitions.
* Implemented F2S bridge reset support and updated related reset
manager registers.
* Expanded SoC64 CPU info reporting.
General maintenance:
* Additional peripherals released from reset for Arria10.
* Cleanup of legacy or incorrect Kconfig implications.
This patch set has been tested on Agilex 5 devkit.
Passing all pipeline tests at:
https://source.denx.de/u-boot/custodians/u-boot-socfpga/-/pipelines/25867
Add a Kconfig option to disable sending Stop conditions between multiple
i2c_msgs within a single xfer. Enable this config by default for ARCH_K3
platforms.
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Repeated Start Condition (Sr) can be used to transfer multiple i2c msgs
without sending a Stop condition (P). So far, the driver default was to
always send a Stop condition after every i2c msg.
Add support for a config option (CONFIG_SYS_I2C_OMAP24XX_REPEATED_START)
to disable sending the Stop condition by default. If this config is
enabled, Stop condition will be sent only if explicitly requested in the
msg flags OR if it is the last msg in the transfer.
Consequently, handle the Repeated Start condition (Sr) in the next msg
by not calling the wait_for_bb() check since it will simply timeout in
the absence of a stop condition (BB will be 1 until Stop is programmed)
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Remove __omap24_i2c_read/write() usage from omap_i2c_xfer() in favour of
the more flexible __omap24_i2c_xfer_msg().
Consequently, these are also no longer needed when DM_I2C is enabled.
New function __omap24_i2c_xfer_msg() will take care of individual read
OR write transfers with a target device. It goes through below sequence:
- Program the provided Target Chip address (OMAP_I2C_SA_REG)
- Program the provided Data len (OMAP_I2C_CNT_REG)
- Program the provided Control register flags (OMAP_I2C_CON_REG)
- Read from or Write to the provided Data buffer (OMAP_I2C_DATA_REG)
For a detailed programming guide, refer to the TRM[0] (12.1.3.4 I2C
Programming Guide).
This patch by itself should be a transparent change. However this is
needed for implementing a proper Repeated Start (Sr) functionality for
i2c_msgs.
Previous implementation for omap_i2c_xfer called __omap24_i2c_read/write
functions, with hardcoded addr=0 and alen=0 for each i2c_msg. Each of
these calls would program the registers always with a Stop bit set, not
allowing for a repeated start between i2c_msgs in the same xfer().
[0]: https://www.ti.com/lit/zip/spruj28 (TRM)
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Remove unused piece of code under CONFIG_I2C_REPEATED_START which does
not have any Kconfig entry at all.
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Jonas KarlmanandKever Yang
Quentin SchulzandKever Yang
Ezra BuehlerandTom Rini
Jiaxun YangandTom Rini
Jerome ForissierandTom Rini
Heinrich SchuchardtandTom Rini
Martin SchillerandHeiko Schocher
Aniket LimayeandHeiko Schocher
Tingting MengandTien Fong Chee