Implement exfat_fs_rename() to rename or move files. This is used
by the 'mv' generic FS interface command. The rename implementation
for other filesystems was added recently and was not part of exfat
porting layer due to merge issue, which made 'mv' command crash,
fix this by adding the missing implementation.
Fixes: b86a651b64 ("fs: exfat: Add U-Boot porting layer")
Signed-off-by: Marek Vasut <marex@denx.de>
Add test for the 'test -e' command to check for existence of files.
This exercises struct fstype_info .exists callback.
Signed-off-by: Marek Vasut <marex@denx.de>
The exfat_fs_exists() should return 0 in case the path does not exist,
and 1 in case the path does exist. Fix the inverted return value. This
fixes 'test -e' command with exfat.
Fixes: b86a651b64 ("fs: exfat: Add U-Boot porting layer")
Signed-off-by: Marek Vasut <marex@denx.de>
The exfat_fs_readdir() depends on state created in exfat_fs_opendir(),
but that state may be disrupted by fs_close() called by the FS layer
in fs_opendir(), because exfat porting layer unmounts the filesystem
in ->close() callback.
To avoid this disruption, avoid creating state in exfat_fs_opendir(),
cache only the directory name to list there, and rework exfat_fs_readdir()
to work in a similar way to exfat_fs_ls(). That is, make exfat_fs_readdir()
open the directory, look up specific entry, extract its properties to be
reported to FS layer, and close the directory. This is slow, but avoids
the disruption. The slowness does not affect regular 'ls' command, which
uses exfat_fs_ls() fast path.
Fixes: b86a651b64 ("fs: exfat: Add U-Boot porting layer")
Signed-off-by: Marek Vasut <marex@denx.de>
Write into a bogus file, like '/.', triggers an "impossible"
print from the exfat core code. That should not be printed
in U-Boot, because U-Boot prints its own error message sooner.
Inhibit this error message.
The following command triggers the bogus print:
"
=> save host 0:0 1000008 /. 0x10
"
Fixes: b86a651b64 ("fs: exfat: Add U-Boot porting layer")
Signed-off-by: Marek Vasut <marex@denx.de>
Make sure the node is never dirty before being released, flush
the node first using exfat_flush_node() and only then release
the node using exfat_put_node(). This now matches the behavior
of exfat_fs_write() too.
Fixes: b86a651b64 ("fs: exfat: Add U-Boot porting layer")
Signed-off-by: Marek Vasut <marex@denx.de>
Tom reports that generating the ESL file we need for authenticated
capsule updates fails to work on azure which expects a RO git tree.
Move it to $(objtree)
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
UART-A can be exposed through uSD, this was tested on Transformer T20
but should work on all Ventana-based boards.
TX is exported on SDD pingroup corresponding to uSD CLK pin
RX is exported on SDB which is CMD pin in uSD slot
Signed-off-by: Artur Kowalski <arturkow2000@gmail.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The Tegra Note 7 is a mini tablet computer and the second Tegra 4
based mobile device designed by Nvidia that runs the Android operating
system. The Tegra Note has a 7" IPS display with 1280 x 800 (217 ppi)
resolution. The 1 GB of RAM and 16 GB of internal memory can be
supplemented with a microSDXC card giving up to 64 GB of additional
storage.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The ASUS Transformer Pad TF701T is an Android tablet computer made by
ASUS, successor to the ASUS Transformer Pad Infinity. The tablet includes
a Tegra 4 T114 processor clocked at 1.9 GHz, and an upgraded 2560×1600
pixel resolution screen, increasing the pixel density to 300 PPI and
a mobile dock. Transformers (t114) board derives from Nvidia Macallan
development board.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The clock initialization routine sets the DISP* clock parent to PLLC,
resulting in DC failure in the case when PLLD was previously configured.
This issue disrupts chainloading and to prevent failures caused by DISP*
clock parent conflicts, clock initialization should not modify DISP*. The
DC driver handles DISP* configuration.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Most device headers contain SoC specific part and common Tegra post part.
Add a generic header which can be used by any Tegra device of one of the
supported SoC generations (T20, T30, T114, T124 or T210) without need in
device specific configuration.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Link CFG_SYS_NS16550_COM1 value to chosen CONFIG_TEGRA_ENABLE_UART Tegra
wide. Remove all CFG_SYS_NS16550_COM1 from device headers.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Applies same logic to general Tegra pincontrol driver as is done to Tegra20
by commit:
a35bf832d7 ("pinctrl: tegra20: detect unknown/invalid pin/func
configurations")
Suggested-by: Artur Kowalski <arturkow2000@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Tegra20 driver doesn't know about some pin configurations and even about
some pins. In case when pin configuration is unknown the pin would be
muxed to whatever is under function 0, in case when pin itself is
unknown, it could cause out-of-bounds array access in pinmux_set_func
and pinmux_set_pullupdown.
Signed-off-by: Artur Kowalski <arturkow2000@gmail.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The Motorola Atrix 4G (MB860) and Droid X2 (MB870) both featured a
dual-core NVIDIA Tegra 2 AP20H processor clocked at 1GHz, coupled with 1GB
of DDR2 RAM. Storage consisted of 16GB of internal flash memory, expandable
via microSD. The display was a 4.0-inch TFT LCD with a resolution of
960x540 pixels (qHD). The devices originally ran on Android up to 2.3
(Gingerbread).
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The LM3532 is a 500-kHz fixed frequency asynchronous boost converter which
provides the power for 3 high-voltage, low-side current sinks. The device
is programmable over an I2C-compatible interface and has independent
current control for all three channels.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add support for the LCD panel module used in Motorola Atrix 4G or Droid X2.
Exact panel vendor and model are unknown. The panel has a 540x960 (qHD)
resolution and uses 24 bit RGB per pixel.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
CPCAP has a dedicated interrupt for power button. Implement this to have
more input control over the devices.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
The CPCAP is a Motorola/ST-Ericsson creation, a multifunctional IC whose
main purpose was power control. It was used in a wide variety of Motorola
products, both Tegra and OMAP based. The most notable devices using this
PMIC are the Motorola Droid 4, Atrix 4G, and Droid X2.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Place Tegra124 SOR and eDP implenetation into common Tegra driver folder
until it is integrated into existing setup.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since this set of drivers suports four Tegra SoC generations, lets name it
just 'tegra'.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
GPIO reset and power-off functionality depends on device tree data, which
is often absent in SPL or TPL. To address this, incorporate PHASE_ into the
config option and add Kconfig option or each phase.
Adjust SYSRESET_GPIO and POWEROFF_GPIO uses to address possible
regressions.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Historically, PLLD2 mirrored PLLD's layout on Tegra30 and 114. However,
with the introduction of Tegra124, this changed. This layout alteration was
not considered, and it now requires a corrective action to prevent future
complications.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
PLLD and PLLD2 clocks possess a unique enable bit within their
miscellaneous register. Take this into account when using clock_set_rate
function.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add missing configuration of chip select polarity. Default polarity is LOW,
which satisfies most cases but some devices require HIGH polarity and will
not work.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Binman includes a good set of tests covering all of its functionality.
This includes a code-coverage test.
However to date the code-coverage test has not been checked
automatically by CI, relying on people to run 'binman test -T'
themselves.
Plug the gap to avoid bugs creeping in future.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Newer lz4 util is not happy with any padding at end of file,
it would abort with error message like:
Stream followed by undecodable data at position 43.
Workaround by skipping testCompUtilPadding test case and manually
strip padding in testCompressSectionSize test case.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
The CheckAddHashValue() function is always called before this one, so
the algorithm check is never used. Replace it with an assert to avoid a
coverage error.
Signed-off-by: Simon Glass <sjg@chromium.org>
Newer versions of the python3-coverage tool require a directory
separator before and after the directory name. Add this so that system
package are not included in the coverage report.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tom Rini <trini@konsulko.com> says:
This series switches to always using $(PHASE_) in Makefiles when
building rather than $(PHASE_) or $(XPL_). It also starts on documenting
this part of the build, but as a follow-up we need to rename
doc/develop/spl.rst and expand on explaining things a bit.
Link: https://lore.kernel.org/r/20250401225851.1125678-1-trini@konsulko.com
Expand the conditional compilation section to explain when to use
CONFIG_IS_ENABLED rather than IS_ENABLED and provide an example. Next,
note what the PHASE_ macro is supposed to be used for as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to make a start on explaining how and when to use certain
macros, we need to document their usage somewhere. As a first step, take
section 21 of the v6.13 Linux Kernel coding-style document on
conditional compilation, verbatim, and add it to our documentation.
Further rewording to be clearer about U-Boot will be done next.
Signed-off-by: Tom Rini <trini@konsulko.com>
It is confusing to have both "$(PHASE_)" and "$(XPL_)" be used in our
Makefiles as part of the macros to determine when to do something in our
Makefiles based on what phase of the build we are in. For consistency,
bring this down to a single macro and use "$(PHASE_)" only.
Signed-off-by: Tom Rini <trini@konsulko.com>
When the `optee hello' subcommand is called, the do_optee_hello_world_ta()
function passes a NULL pointer to the strcmp() function while verifying its
input argument, which results in the following crash:
=> optee hello
"Synchronous Abort" handler, esr 0x96000010, far 0x0
Fix this by verifying the number of input arguments instead.
Fixes: e3cf80fbe0 ("cmd: Add support for optee commands")
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Jerome Forissier <jerome.forissier@linaro.org>
Cc: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Jerome Forissier <jerome.forissier@linaro.org>
The number of memory banks in QEMU is not bounded by 1.
In this example we have two banks:
qemu-system-aarch64 \
-machine virt \
-nographic \
-cpu cortex-a72 \
-m 8G \
-smp 8,sockets=2,cores=4,threads=1 \
-object memory-backend-ram,id=mem0,size=4G \
-numa node,cpus=0-3,memdev=mem0 \
-object memory-backend-ram,id=mem1,size=4G \
-numa node,cpus=4-7,memdev=mem1 \
-bios u-boot.bin
Use the default value defined in /Kconfig as 4.
Suggested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Suggested-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The AM62x uses the DA8XX (DaVinci) GPIO controller. Enable
CONFIG_DA8XX_GPIO to support GPIO access from the Cortex-A53.
Also enable the 'gpio' command to allow users to interact
with GPIOs from the U-Boot shell.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This enables the 'rproc' command, allowing users to
start, stop, and manage co-processors as well as load firmware
images.
Useful for systems with auxiliary cores, such as the M4 core
in the AM62x soc.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This enables the 'rproc' command, allowing users to
start, stop, and manage co-processors as well as load firmware
images.
Useful for systems with auxiliary cores, such as M4 or R5 cores
in the AM64x soc.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Marek VasutandTom Rini
Ilias ApalodimasandTom Rini
Artur KowalskiandSvyatoslav Ryhel
Simon GlassandTom Rini
Jiaxun YangandTom Rini
Vincent StehléandTom Rini
Heinrich SchuchardtandTom Rini
Daniel SchultzandTom Rini