Hrushikesh Salunke <h-salunke@ti.com> says:
This series enables PCIe Endpoint mode on TI's J784S4 SoC. The J784S4
SoC features two Cadence PCIe controller instances (PCIe0 and PCIe1)
that can operate in endpoint mode. This series adds support for
configuring these controllers with up to 4 lanes.
Key changes include:
- Adding a stabilization delay after power domain reset to prevent
timing-related initialization issues
- SERDES mux configuration support for proper lane routing, which is
essential for SoCs where SERDES lanes are shared between multiple
controllers (PCIe, USB, etc.) with different configurations across
boot phases
- J784S4 SoC endpoint configuration with 4-lane support
- Disabling unconfigured endpoint functions to prevent enumeration
issues on the Root Complex side
This series has been tested on J784S4 EVM with PCIe endpoint boot
configuration. Following are the corresponding test logs.
https://gist.github.com/hrushikesh221/331d65f45f43fd138f57e6adb61c4332
Link: https://lore.kernel.org/r/20251023114604.3655625-1-h-salunke@ti.com
Guillaume La Roque (TI.com) <glaroque@baylibre.com> says:
This series adds EEPROM board detection support for AM62x and refactors
the board detection code across AM6x family boards to eliminate code
duplication.
The series introduces two new generic functions for AM6x boards:
- do_board_detect_am6(): Reads the on-board EEPROM with fallback logic
to alternate I2C addresses
- setup_serial_am6(): Sets up the serial number environment variable
from EEPROM data
Link: https://lore.kernel.org/r/20251103-am62xeeprom-v3-0-e390779c0fc5@baylibre.com
Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu> says:
This patch series adds basic support for the boards based on Airoha
EN7523/EN7529/EN7562 SoCs. Due to ATF restrictions these boards are
able to run 32-bit OS only.
This patch series adds support for the following hardware:
* console UART
* ethernet controller/switch
* spinand flash (in non-dma mode)
The following issues may be expected:
* Extra slow UBI attaching in U-Boot (up to 20 sec with fastmap enabled).
This is caused by the lack of DMA support in the U-Boot airoha-snfi driver.
* Linux airoha-snfi driver in some cases might damage you flash data
(see: https://lore.kernel.org/lkml/20251012121707.2296160-15-mikhail.kshevetskiy@iopsys.eu/)
* Latest linux kernel is recommended to properly support flashes
with more than one plane per lun
(see: https://lore.kernel.org/lkml/20251012121707.2296160-7-mikhail.kshevetskiy@iopsys.eu/)
* It's NOT recommended to use flashes working in continuous mode because
U-Boot airoha-snfi driver does not support such flashes properly.
The patches was tested on the board:
- SoC: Airoha EN7562
- RAM: 512 MB
- SPI NAND: 4 Gbit, made by Toshiba
- Linux boot: was NOT tested
The U-Boot was chain-loaded from the running U-Boot. Airoha ATF-2.3 does
not allow easily chain-loading of U-Boot from U-Boot, so a special FIT
image (mimic linux kernel) was created
1) Create u-boot.its file with the following contents:
=== cut here ===
/dts-v1/;
/ {
description = "ARM OpenWrt FIT (Flattened Image Tree)";
#address-cells = <1>;
images {
u-boot-ram {
description = "OpenWrt U-Boot RAM image";
data = /incbin/("u-boot.bin.lzma");
type = "kernel";
arch = "arm";
os = "linux";
compression = "lzma";
load = <0x81e00000>;
entry = <0x81e00000>;
hash@1 {
algo = "crc32";
};
hash@2 {
algo = "sha1";
};
};
fdt-1 {
description = "OpenWrt device tree blob";
data = /incbin/("dts/upstream/src/arm/airoha/en7523-evb.dtb");
type = "flat_dt";
arch = "arm";
compression = "none";
hash@1 {
algo = "crc32";
};
hash@2 {
algo = "sha1";
};
};
};
configurations {
default = "config-ram-uboot";
config-ram-uboot {
description = "OpenWrt RAM U-Boot";
kernel = "u-boot-ram";
fdt = "fdt-1";
};
};
};
==================
2) Create u-boot.itb image to chain-load new u-boot from the old one
lzma_alone e u-boot.bin u-boot.bin.lzma
mkimage -f u-boot.its u-boot.itb
3) Load new u-boot from the old one
U-Boot> tftpboot u-boot.itb && bootm
Link: https://lore.kernel.org/r/20251101004503.2379529-1-mikhail.kshevetskiy@iopsys.eu
TI's J784S4 SoC has two instances of PCIe Controller namely PCIe0 and
PCIe1 which are Cadence PCIe Controllers. Enable corresponding configs
to support PCIe Endpoint mode of operation on these instances.
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
TI's J784S4 SoC has two instances of PCIe Controller namely PCIe0 and
PCIe1 which are Cadence PCIe Controllers. Add support to configure PCIe
instances in Endpoint mode of operation.
While at it disable all endpoint functions except function 0 during
probe to prevent the Root Complex from enumerating unconfigured
functions. This ensures only properly configured endpoint functions
are visible to the host and avoids enumeration issues with
multi-function devices.
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Probe the mux device early in the SERDES configuration flow to ensure
proper lane routing before PHY initialization. This is required for SoCs
where SERDES lanes can be muxed between different controllers
(PCIe, USB, etc), and different mux configurations are required between
different boot phases.
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Add a 1ms delay after powering on the PCIe power domain to ensure
the controller stabilizes before subsequent operations. This prevents
potential timing issues during PCIe endpoint initialization.
The delay allows sufficient time for the power domain to fully come
up and the hardware to be in a stable state before configuration
begins.
Signed-off-by: Hrushikesh Salunke <h-salunke@ti.com>
Replace the board-specific implementation of do_board_detect()
with a call to the generic do_board_detect_am6() function to
avoid code duplication across AM6x family boards.
The generic function provides the same functionality with
additional fallback logic to try alternate EEPROM addresses.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Signed-off-by: Guillaume La Roque (TI.com) <glaroque@baylibre.com>
Replace the board-specific implementation of do_board_detect() and
setup_serial() with calls to the generic do_board_detect_am6() and
setup_serial_am6() functions.
The generic function provides the same functionality with
additional fallback logic to try alternate EEPROM addresses.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Signed-off-by: Guillaume La Roque (TI.com) <glaroque@baylibre.com>
I2C EEPROM data contains the board name and its revision.
Add support for:
- Reading EEPROM data and store a copy at end of SRAM
- Updating env variable with relevant board info
- Printing board info during boot
Use the generic do_board_detect_am6() and setup_serial_am6()
functions to avoid code duplication across AM6x family boards.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Signed-off-by: Guillaume La Roque (TI.com) <glaroque@baylibre.com>
Add two new generic functions for AM6x family boards to simplify
board-specific implementations:
- do_board_detect_am6(): Generic board detection function that reads
the on-board EEPROM. It first attempts to read at the configured
address, and if that fails, tries the alternate address
(CONFIG_EEPROM_CHIP_ADDRESS + 1). This provides a common
implementation that can be used across different AM6x boards.
- setup_serial_am6(): Sets up the serial number environment variable
from the EEPROM data. The serial number is converted from
hexadecimal string format to a 16-character hexadecimal
representation and stored in the "serial#" environment variable.
Both functions are protected by CONFIG_IS_ENABLED(TI_I2C_BOARD_DETECT)
and are designed to be used by AM62x, AM64x, AM65x, and other AM6x
family boards.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@kernel.org>
Signed-off-by: Guillaume La Roque (TI.com) <glaroque@baylibre.com>
This allow us remove some an7581/an7583 specific code and use a common
code instead.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
This patch unify probing code using airoha SCU regmap helper, thus a
common function can be used instead of an7581/an7583 specific ones.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
In preparation for support for Airoha AN7583, convert the driver to
regmap API. This is needed as Airoha AN7583 will use syscon to access
reset registers.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This adds clock driver for airoha en7523/en7529/en7562 SoCs. The code
is based on corresponding linux driver.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
We need access SCU and CHIP_SCU regmaps in several places (clk-airoha,
reset-airoha, airoha_eth). Unfortunately these regmaps can't be easily
retrieved with a common code, because of different Airoha SoCs uses
a different dts structure.
To make life easy we can write a commonly named SoC specific helpers
for these tasks. This patch implements helpers for Airoha EN7523 SoC.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
We need access SCU and CHIP_SCU regmaps in several places (clk-airoha,
reset-airoha, airoha_eth). Unfortunately these regmaps can't be easily
retrieved with a common code, because of different Airoha SoCs uses
a different dts structure.
To make life easy we can write a commonly named SoC specific helpers
for these tasks. This patch implements helpers for Airoha AN7581 SoC.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Basic support for en7523/en7529/en7562 SoCs. Within a patch
only serial console will be supported.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
This is required because airoha/en7523 will be added with the following
patches. Without this line config for en7523 will be created instead of
an7581.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Clean up the sound Kconfig options to let all sound devices depend on
CONFIG_SOUND.
Before this patch it was possible to select CONFIG_SOUND_MAX98357A even
with CONFIG_SOUND=n.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the resource management configuration (rm-cfg.yaml) to align
with the default configuration provided in TI's AM62xx Processor SDK
Linux version 11.01.05.03, generated using the K3 Resource Partitioning
Tool.
This matches the configuration from board/ti/am62x/rm-cfg.yaml and the
notable change is the sharing of MCU GPIO interrupts between DM R5 and
A53 cores, and reservation of an additional virtual interrupt and event
for TIFS usage.
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Anshul Dalal <anshuld@ti.com>
If missing, lbaint_t typedef will not be found in some cases.
[The proper fix for the commit above at the time would have been to
include ide.h as only since commit 1a73661bc7 ("dm: Add a new header
for block devices") is the typedef in blk.h]
Fixes: 04735e9c55 ("Fix ext2/ext4 filesystem accesses beyond 2TiB")
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
The general python documentation for the subprocess class recommends
that run() be used in all cases that it can handle. What we do in
RunAndLog is simple enough that run() is easy to switch to. In fact,
looking at this exposed a problem we have today, which is that we had
combined stdout and stderr but then looked at both stdout and stderr as
if they were separate. Stop combining them.
Signed-off-by: Tom Rini <trini@konsulko.com>
Quentin Schulz <foss+uboot@0leil.net> says:
This improves readability in menuconfig by putting PWM symbols under a
Kconfig menu.
It also groups PWM symbols that depend on DM_PWM together under an if
DM_PWM block so that we don't need to always list the dependency in the
depends on of the symbol.
No intended change in behavior except how it shows in menuconfig.
Link: https://lore.kernel.org/r/20251030-pwm-kconfig-v2-0-d151a42784ce@cherry.de
This simplifies the "depends on" since we don't need DM_PWM listed
explicitly there as it already is made explicit via the surrounding
"if". No intended change in behavior.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Since it is registered as a U_CLASS_DRIVER, Sandbox PWM driver is a
Driver Model Driver and thus to be usable depends on DM_PWM to be
selected.
Let's make sure of that via the appropriate Kconfig option.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
So it's visually better split from the other subsystems when using
menuconfig.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Pull request efi-2026-01-rc2
CI: https://source.denx.de/u-boot/custodians/u-boot-efi/-/pipelines/28208
Documentation:
* bootstd: Describe environment variable extension_overlay_addr
environment and remove extension support from TODO list
EFI:
* Correct the detection of the video mode in the EFI payload app:
- Use struct efi_gop_mode_info in the definition of struct
efi_entry_gopmode.
- In function get_mode_from_entry() use the correct type for the video
mode structure.
* Use a valid error code as return value in efi_store_memory_map().
* Avoid a memory leak for the variable name in efi_bl_create_block_device().
* Correct the code indentation in efi_uc_stop().
* Correct the description of struct efi_priv.
* Fix typos in code comments.
Other:
* qfw: Add more fields and a heading to qfw list
* Fix the support for ACPI pass-through on ARM and RISC-V:
Avoid zeroing out the XSDT address
* test: provide unit test for 'acpi list' command
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAmkNj/kACgkQxIHbvCwF
# GsS8NQ/6Aj+Z54HJTIEfoXssvElLr5ATactrCxszq42i/yy6dLqa2Ym1afG6w1XS
# 1ZbCeU/bCXFke5Tsz+x89gEfckUm83oTwngwcID0WR1qn8mWjwR7tM5MuORq8NxU
# 7NwLuFs9O/QZihagKdz6hv1/Y+cBwiAYLY16EYVSuUlbLaKQo3QvxwWkqG3jdKWV
# Rm58/PolU+2h04MBwP0SxSduX4OyRF/tMOGjf5RGLyqCyj8kIgdu7PvUAPMM+Gps
# KemL59V0Bdv8hlF4JknmPz+idtZg2nHIDdNrBZvoxwzwGQeRZ1YXAMruRxZXqDYL
# tiuDp6HMv/GfIIGkz14tJtJMdboaAybAnluPWGalx8JQJqJzEPww0R+9s4KKQeWL
# mHgRyl6PxVV9p19f79Qq6q6ETwrFDX0YH3pdrGUk3DBa3lDt0UsEAnuW4FvaJ8tx
# 3PMrjKAxpxocT0hglsMVnptnfvDEigMsjwH/TWrau83mY+juxFQLjm+U4vye+qCa
# 4zXjjLas18+eRcrv2KxU7teakyi1Jp+WbqHq37L26YcQMaLq/RkBc0bTrsreKKLu
# jprYFpvc7EJpH2Fd1XWaZ2EnxXcVSJSvrY/iwRQqb6wbwQ6XGtMvSh3IFY8IzAoh
# N2Pj78oaYqyL1q/TftuZWhEHo3a0M/HfM4D+oMSHzJtWCb0wZHE=
# =OGcS
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 07 Nov 2025 12:21:45 AM CST
# gpg: using RSA key 6DC4F9C71F29A6FA06B76D33C481DBBC2C051AC4
# gpg: Good signature from "Heinrich Schuchardt <xypron.glpk@gmx.de>" [unknown]
# gpg: aka "[jpeg image of size 1389]" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6DC4 F9C7 1F29 A6FA 06B7 6D33 C481 DBBC 2C05 1AC4
Add DWMCI_QUIRK_DISABLE_FMP flag to Exynos850 driver data to make the
driver disable FMP in case of Exynos850 chip. That makes eMMC on
Exynos850 functional when U-Boot is executed during USB boot.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Up until now "samsung,exynos7-dw-mshc-smu" compatible was used for
Exynos850 SoC, as it's present in its device tree. But Exynos850 device
tree also supports "samsung,exynos850-dw-mshc-smu" compatible string.
Add it in compatible ID list in the driver so that it can be matched
against this string for Exynos850 device tree.
No functional change, as the driver data is just a copy of
"samsung,exynos7-dw-mshc-smu" data for now.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
