Radxa E20C has three gpio controlled leds (sys, wan and lan).
Add led nodes and set default trigger to heartbeat for the sys led and
netdev for the lan and wan leds.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250304201642.831218-2-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 6a709e003492e9878d5f1357be0b2e1162e1e6a6 ]
(cherry picked from commit a3556ede6b48c7760ac3608ad77601fca26d2ce0)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa E20C route UART0 M0 pins (GPIO4_C7 and GPIO4_D0) to the onboard
CH340B for debug console use.
Add pinctrl for UART0 M0 pins used for serial console.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250228064024.3200000-6-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 0d2312f0d3e4ce74af0977c1519a07dfc71a82ac ]
(cherry picked from commit 9bcf6ccdd87c3be48fe7d75150c6e403c5c0a42d)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Quality-of-Service (QsS) node stores/restores specific
register contents when the power domains is turned off/on.
Add QoS node so that they can connect to the power domain.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://lore.kernel.org/r/20250306123809.273655-3-amadeus@jmu.edu.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 61a05d8ca3030a544175671f5fab7a8f29c24085 ]
(cherry picked from commit 9ee90dfd6957fcc42ea94c43d195b01d1b286713)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add pinctrl and gpio nodes for RK3528 and import rk3528-pinctrl.dtsi
from vendor linux-6.1-stan-rkr5 kernel with the hdmi-pins-idle node
removed due to missing label reference to pcfg_output_low_pull_down.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20250228064024.3200000-5-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: a31fad19ae39ea27b5068e3b02bcbf30a905339b ]
(cherry picked from commit 89a24fa2e923b68a42ccc8cc9cb2d5bdf291ac40)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add dt node for RK3528 clock and reset unit. Clock "gmac0_clk" is
generated by internal Ethernet phy, a fixed clock node is added as a
placeholder to avoid orphans.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Link: https://lore.kernel.org/r/20250217061142.38480-9-ziyao@disroot.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: 858cdcdd11cf9913756297d3869e4de0f01329ea ]
(cherry picked from commit 60741472b42e92d2393327cb70669ab90e3b382f)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There are two types of clocks in RK3528 SoC, CRU-managed and
SCMI-managed. Independent IDs are assigned to them.
For the reset part, differing from previous Rockchip SoCs and
downstream bindings which embeds register offsets into the IDs, gapless
numbers starting from zero are used.
Signed-off-by: Yao Zi <ziyao@disroot.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250217061142.38480-6-ziyao@disroot.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
[ upstream commit: e0c0a97bc308f71b0934e3637ac545ce65195df0 ]
(cherry picked from commit 8768d063e732e64892e4d1d09aa583d1394c8388)
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Linux commit 6ee0b9ad3995 ("arm64: dts: rockchip: Add rng node to
RK3588") merged for v6.15-rc1 add a proper rng node to the device tree.
The compatible used differs compared to what U-Boot is currently using.
Replace the old trngv1 compatible with the dts/upstream compatible in
the rng driver and remove the old rng node compatible override from SoC
u-boot.dtsi to keep rng working after the driver change.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Linux commit afeccc408496 ("arm64: dts: rockchip: add DT entry for RNG
to RK356x") merged for v6.12-rc1 add a proper rng node to the SoC DT.
Remove the rng node from SoC u-boot.dtsi now that the rng driver support
the compatible used in dts/upstream DT. Ensure the rng node is enabled
to support rng on RK3566 variants.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Linux commit afeccc408496 ("arm64: dts: rockchip: add DT entry for RNG
to RK356x") merged for v6.12-rc1 add a proper rng node to the SoC DT.
The compatible used differs compared to what U-Boot is currently using.
Add support for the rk3568-rng used in upstream Linux. Support for the
cryptov2-rng compatible is still kept because PX30/RK3326 and RK3308 are
still using it.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The meminfo and rng commands are helpful for testing, enable them.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The meminfo and rng commands are helpful for testing, enable them.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
BOARD_LATE_INIT is already selected by ROCKCHIP_RK3588 so there is no
need to select it under any board target config.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
BOARD_LATE_INIT is already selected by ROCKCHIP_RK3568 so there is no
need to select it under any board target config.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Ensure rk3588_common.h can be used by boards directly by defining a
blank ROCKCHIP_DEVICE_SETTINGS unless it already is defined.
Add a default SYS_CONFIG_NAME to include rk3588_common.h unless a board
target overrides it in its board Kconfig.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Ensure rk3568_common.h can be used by boards directly by defining a
blank ROCKCHIP_DEVICE_SETTINGS unless it already is defined.
Add a default SYS_CONFIG_NAME to include rk3568_common.h unless a board
target overrides it in its board Kconfig.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Ensure ROCKCHIP_DEVICE_SETTINGS is defined before including
rk3588_common.h in board include/configs files.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Ensure ROCKCHIP_DEVICE_SETTINGS is defined before including
rk3568_common.h in board include/configs files.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The partitions env variable is using an outdated partition layout that
is typically expected to be used with older vendor miniloader blobs.
Rockchip devices will run fine using any partition layout if the first
16 MiB of MMC storage is ignored/skipped.
Remove the partitions env variable to stop encourage users a continued
use of this outdated partition layout on RK3588 devices.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The partitions env variable is using an outdated partition layout that
is typically expected to be used with older vendor miniloader blobs.
Rockchip devices will run fine using any partition layout if the first
16 MiB of MMC storage is ignored/skipped.
Remove the partitions env variable to stop encourage users a continued
use of this outdated partition layout on RK356x devices.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Define constants for hptimer reg names and use them instead of magic
numbers in rockchip_stimer_init().
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip RK3576 SoC uses a different DRAM base address, 0x40000000,
compared to prior SoCs.
Add default options that should work when 0x40000000 is used as DRAM
base address. Use same offsets as before, just below 64 MiB.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
New Rockchip SoCs will typically require use or an external TPL when
support for the SoC is added to U-Boot.
Move imply ROCKCHIP_EXTERNAL_TPL under SoC Kconfig symbol to remove a
future likelihood of a long "default y if" line.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The ROCKCHIP_COMMON_STACK_ADDR Kconfig option was originally enabled
in the SoC specific Kconfig files to ease during the initial migration
to use common stack addresses.
All boards for the affected SoCs have been migrated to use common stack
addresses. Migrate to use an imply under the SoC symbol instead of
re-define the symbol in each SoC specific Kconfig file.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A few Rockchip ARMv7 SoCs use 0x60000000 as DRAM base address instead of
the more common 0x0 DRAM base address used on AArch64 SoCs.
Add default options that should work for these ARMv7 SoCs. Same offsets
as before are used, just below 64 MiB. Hex values have also been padded
to improve alignment.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The stack-pointer addresses used with ROCKCHIP_COMMON_STACK_ADDR expect
that DRAM is initialized by TPL or ROCKCHIP_EXTERNAL_TPL, that SPL has
access to full DRAM and SPL is loaded to/executed from start of DRAM.
Add depends on to ensure use of the ROCKCHIP_COMMON_STACK_ADDR symbol
does not cause problem for any board not using TPL and back-to-BROM
loading of SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Kconfig symbol ROCKCHIP_COMMON_STACK_ADDR currently imply the
TPL_ROCKCHIP_COMMON_BOARD option when TPL=y. This is inconvenient for a
SoC with very limited SRAM to use a custom tpl.c together with the
common stack addresses.
Move any imply TPL_ROCKCHIP_COMMON_BOARD to under the SoC symbol, where
it belongs. Add the missing imply to RK3328 and PX30 use a SoC specific
tpl.c and only expect imply TPL_LIBGENERIC_SUPPORT.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Haikou carrierboard allows multiple adapter boards to be connected, for
now there exists the following adapter boards compatible with PX30
Ringneck:
- Haikou Video Demo on the Video Connector,
- Haikou LVDS 9904379 on the Video Connector,
So support DT overlays so we can use this mechanism instead of full DTB
containing both the carrierboard and the adapter.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to be able to use Device Tree Overlays, the fdtoverlay_addr_r
needs to be specified.
Follow what's been done for other Rockchip SoCs and leave 1MiB for the
base DTB before the address for the overlay.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
I don't see a reason why this should only be enabled on a per-board
basis. The rng IP is inside the SoC and doesn't seem to rely on anything
external to it, therefore let's enable it on the SoC DTSI and remove the
now empty px30-evb-u-boot.dtsi.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The build system uses HAVE_VENDOR_COMMON_LIB to automatically include
board/$(VENDOR)/common/Makefile, therefore let's use that to implicitly
include board/theobroma-systems/common/Makefile and compile the common.c
file when building proper.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Nothing is calling the function rk_board_init() and the io-domain driver
can handle the functions intended purpose based on information from DT.
Cleanup by removing the unused rk_board_init() function and re-sort
included headers.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The default value of 0x800000 (8 MB) is somewhat limiting for us, as our
compressed kernel may grow up to around 4 MB. By choosing the commonly
used value of 0x2000000 (32 MB), we are definitely on the safe side.
This rather large amount should be fine, as we have 128 MB of RAM.
Signed-off-by: Ezra Buehler <ezra.buehler@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Jiaxun Yang <jiaxun.yang@flygoat.com> says:
This is a huge series which promoted MIPS/Boston target into a
usable state, with fixes to drivers and general framework issues
I found in this process.
I also converted the target to OF_UPSTREAM.
This target is covered by QEMU, to test on QEMU:
```
make boston64r6el_defconfig
make
qemu-system-mips64el -M boston -cpu I6500 -bios ./u-boot.bin -nographic
```
Link: https://lore.kernel.org/r/20240517-boston-v3-0-1ea7d23f4a1d@flygoat.com
Paul had left MIPS a couple of years ago, his email address is
no longer valid.
Replace it with his kenrel.org email, which has been used in
kernel and QEMU, in case we still want to reach him.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
In upstream devicetree, clk_boston is a child of syscon node
and there is no "regmap" property for clk_boston node.
Try to check parent device first to look for syscon.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Provide default environment variables on image loading address
to make the board useful.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This is a PC-like platform board.
Enable drivers for most on-board devices to make it useful.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Remove hard dependencies to arch headers, get clock from clk
subsystem if arch clock function is not available, align
compatible strings with devicetree binding.
No functional change on existing platforms, just get it build
on other platforms.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Ensure that we are using correct physical/virtual address for
DMA buffer write and hardware register settings.
The convention is: in ahci_ioports all pointers are virtual,
that will be converted to physical address when writing to
hardware registers or into sg/cmd_tbl.
Also fixed 64bit physical address support for dwc_ahsata, ensure
higher bits are written into registers/sg properly.
Use memalign for allocating aligned buffer in dwc_ahsata so we
don't have to do our own alignment in driver.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
For MIPS we are always looking gd->dram in virtual address so
PCI_MAP_SYSTEM_MEMORY should always be enabled.
If in future we ever want to make it physical we have to set
ARCH_MAP_SYSMEM.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Boston has a very limited memory range for PCI controllers, where
1MB can't easily fit into it.
Make alignment boundary of PCI memory resource allocation a Kconfig
option and default to 0x10000 for boston.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Jonas KarlmanandKever Yang
Chukun PanandKever Yang
Yao ZiandKever Yang
Nicolas FrattaroliandKever Yang
Quentin SchulzandKever Yang
Ezra BuehlerandTom Rini
Jiaxun YangandTom Rini