Convert the board to use DM_PMIC instead of the legacy SPL I2C/PMIC
handling.
Changes include:
- Enable DM_PMIC, DM_PMIC_PCA9450, and SPL_DM_PMIC_PCA9450 in defconfig.
- Drop legacy SPL I2C and PMIC options.
- Remove manual I2C1 pad setup and legacy power_pca9450_init() usage.
- Use DM-based pmic_get() with the DT node "pmic@25".
- Update PMIC register programming to use struct udevice API.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert the board to use DM_PMIC instead of the legacy SPL I2C/PMIC
handling.
Changes include:
- Enable DM_PMIC, DM_PMIC_PCA9450, and SPL_DM_PMIC_PCA9450 in defconfig.
- Drop legacy SPL I2C and PMIC options.
- Remove manual I2C1 pad setup and legacy power_pca9450_init() usage.
- Use DM-based pmic_get() with the DT node "pmic@25".
- Update PMIC register programming to use struct udevice API.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Convert the board to use DM_PMIC instead of the legacy SPL I2C/PMIC
handling.
Changes include:
- Enable DM_PMIC, DM_PMIC_PCA9450, and SPL_DM_PMIC_PCA9450 in defconfig.
- Drop legacy SPL I2C and PMIC options.
- Remove manual I2C1 pad setup and legacy power_pca9450_init() usage.
- Use DM-based pmic_get() with the DT node "pmic@25".
- Update PMIC register programming to use struct udevice API.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Convert the board to use DM_PMIC instead of the legacy SPL I2C/PMIC
handling.
Changes include:
- Enable DM_PMIC, DM_PMIC_PCA9450, and SPL_DM_PMIC_PCA9450 in defconfig.
- Drop legacy SPL I2C and PMIC options.
- Remove manual I2C1 pad setup and legacy power_pca9450_init() usage.
- Use DM-based pmic_get() with the DT node "pmic@25".
- Update PMIC register programming to use struct udevice API.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
On the SMARC iMX95 the WiFI UART and JTAG signals are shared. The
WIFI_UART_EN signal is used to select between these two modes.
Currently, there is no hog present in the device tree but the
configuration needs to be added, as once the device tree comes from
mainline Linux, a hog will drive WIFI_UART_EN high to select by
default the UART function during boot.
Enable CONFIG_GPIO_HOG to apply gpio-hog definitions in the device tree.
Signed-off-by: Franz Schnyder <franz.schnyder@toradex.com>
Allow CONFIG_OF_UPSTREAM to receive automatic device tree updates for
the Toradex SMARC iMX95.
Remove the now obsolete device tree files:
- imx95-toradex-smarc-dev.dts
- imx95-toradex-smarc.dtsi
Signed-off-by: Franz Schnyder <franz.schnyder@toradex.com>
This platform enables CONFIG_BOARD_EARLY_INIT_F and then has a
do-nothing board_early_init_f function. Change to not enabling the
option and so not needing an empty function.
Signed-off-by: Tom Rini <trini@konsulko.com>
This platform enables CONFIG_BOARD_EARLY_INIT_F and then has a
do-nothing board_early_init_f function. Change to not enabling the
option and so not needing an empty function.
Signed-off-by: Tom Rini <trini@konsulko.com>
This platform enables CONFIG_BOARD_EARLY_INIT_F and then has a
do-nothing board_early_init_f function. Change to not enabling the
option and so not needing an empty function.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This platform enables CONFIG_BOARD_EARLY_INIT_F and then has a
do-nothing board_early_init_f function. Change to not enabling the
option and so not needing an empty function.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This platform enables CONFIG_BOARD_EARLY_INIT_F and then has a
do-nothing board_early_init_f function. Change to not enabling the
option and so not needing an empty function.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This platform enables CONFIG_BOARD_EARLY_INIT_F and then has a
do-nothing board_early_init_f function. Change to not enabling the
option and so not needing an empty function.
Signed-off-by: Tom Rini <trini@konsulko.com>
This platform enables CONFIG_BOARD_EARLY_INIT_F and then has a
do-nothing board_early_init_f function. Change to not enabling the
option and so not needing an empty function.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This platform enables CONFIG_BOARD_EARLY_INIT_F and then has a
do-nothing board_early_init_f function. Change to not enabling the
option and so not needing an empty function.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
This platform enables CONFIG_BOARD_EARLY_INIT_F and then has a
do-nothing board_early_init_f function. Change to not enabling the
option and so not needing an empty function.
Signed-off-by: Tom Rini <trini@konsulko.com>
In the case of SPI_XFER_BEGIN | SPI_XFER_END, the function creates a
buffer of double the size of the transaction, so that it can write the
data in into the second half. It sets the rx_offset to len, and in the
while loop we are setting an internal "din" to buffer + rx_offset.
However, at the end of each loop, the driver copies "buffer + 2 *
cmd_len" back to the data_in pointer.
This commit changes the source of the data to buffer + rx_offset.
Signed-off-by: Tomas Alvarez Vanoli <tomas.alvarez-vanoli@hitachienergy.com>
The CAAM JR driver is initialized from arch_misc_init(). If
ARCH_MISC_INIT is not enabled, the driver is never initialized,
which can lead to crashes or hangs (e.g. during hash operations).
Select ARCH_MISC_INIT when enabling FSL_CAAM to ensure proper
initialization.
Signed-off-by: Heiko Schocher <hs@nabladev.com>
Suggested-by: Fabio Estevam <festevam@nabladev.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
New SoM revision use series termination for eMMC signals while older do
not. To prevent signal overshot on older revisions, DSR must be set and
limited. The eMMC type is used to differentiate between revisions.
Keep a table with all types, that are known to require DSR.
Signed-off-by: Paul Gerber <Paul.Gerber@ew.tq-group.com>
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Update functions to use the common baseboard header and
select TQ_COMMON_BB Kconfig option for MBa6 and WRU4.
While at it, remove empty implementations that are now covered by
board/tq/common.
Signed-off-by: Paul Gerber <Paul.Gerber@ew.tq-group.com>
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
TQMa6 and other SoMs from TQ-Systems GmbH need a baseboard. Therefore
functionality of U-Boot board callbacks may be distributed between SoM
and baseboard implementation.
To prevent code duplication and boilerplate implement a baseboard specific
API for TQ boards with weak defaults that can be filled out for baseboard
implementations as needed.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
The SoM (TQMa6) can be used on various baseboards. No modifications to
the SoM files should be required to use the SoM on different baseboards.
Therefore, include the SoM headers in the baseboard.
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Remove the definition of CFG_POWER_PFUZE100_I2C_ADDR and
TQMA6_PFUZE100_I2C_BUS as it is not used.
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
Prepare moving boiler plate code out of board confguration header and
prepare to share a lot of things between boards.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Max Merchel <Max.Merchel@ew.tq-group.com>
As the PHYTEC phyCORE-i.MX91 [1] is just another variant of the existing
PHYTEC phyCORE-i.MX93 SoM but with i.MX91 SoC populated instead, add it
to the existing board-code "phycore_imx93", and rename that board to
"phycore_imx91_93" to reflect the dual SoCs support. While at it, also
rename and change common files accordingly. This way i.MX91 and i.MX93
SoC variants of the phyCORE SoM share most of the code and documentation
without duplication, while maintaining own device-tree and defconfigs
for each CPU variant.
Supported features:
- 1GB LPDDR4 RAM
- Debug UART
- EEPROM
- eMMC
- Ethernet
- SD-card
- USB
Product page SoM:
[1] https://www.phytec.eu/en/produkte/system-on-modules/phycore-imx-91-93/
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
The driver requests explicitly "reset-gpio" property, not the one with
"gpios" suffix but upstream Linux kernel deprecated it in 2021.
Existing upstream Linux kernel DTS is being changed to "reset-gpios"
property, thus update the driver to read that one too.
Note that driver is probably broken already, because it parsed GPIO in
standard way respecting the flags and on top of that applied the
"reset-gpio-active-high" flag, thus "reset-gpio ACTIVE_LOW" with the
"reset-gpio-active-high" property would be double inverted.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Pull request net-20260331.
net:
- airoha_eth & pcs_airoha driver fixes
- Rework some symbol dependencies
- dwc_eth_xgmac: Move DMA reset and pad calibration after PHY init
- rtl8169: add support for RTL8125d
- rswitch: Avoid NULL pointer dereference during PHY access
- rswitch: Remap CPU to bus addresses using dev_phys_to_bus()
- phy: dp83867: reset PHY on init to ensure clean state
net-lwip:
- nfs: fix buffer overflow when using symlinks
- tftp: update image_load_addr after successful transfer
[trini: Add missing "if NET" to CMD_DHCP select's CMD_BOOTP]
Signed-off-by: Tom Rini <trini@konsulko.com>
Use dev_phys_to_bus() to convert CPU addresses of DMA descriptors
into bus addresses of DMA descriptors. This is necessary on hardware
which does not have 1:1 mapping between CPU and memory addressed by
the DMA. This has no impact on other hardware which does not need
this conversion.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
After a warm reboot, the PHY is left in power-down state
(BMCR_PDOWN set) causing auto-negotiation to timeout when
running the dhcp command.
Fix this by calling phy_reset() in dp83867_config() which
brings the PHY to a known clean state. The existing
DP83867_SW_RESTART is removed as it is redundant after phy_reset().
Fixes: 721aed7912 ("net: phy: Add support for Texas Instruments DP83867")
Signed-off-by: Pranav Tilak <pranav.vinaytilak@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
do_tftpb() parses the load address into a local variable laddr but
never updates the global image_load_addr. Commands that rely on
image_load_addr as their default address (e.g. 'bmp info')
therefore operate on the wrong address when called without
an explicit argument after tftpboot.
Update image_load_addr to laddr only on a successful transfer, so
that it accurately reflects where data was actually loaded.
Fixes: 4d4d783812 ("net: lwip: add TFTP support and tftpboot command")
Signed-off-by: Pranav Sanwal <pranav.sanwal@amd.com>
Reviewed-by: Jerome Forissier <jerome.forissier@arm.com>
At the very early stage when PHY ID is being auto-detected, the
PHY device is not yet instantiated and rswitch_etha .phydev is
still NULL. Add missing check for this condition and perform C22
fallback access in this PHY ID auto-detection case.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The HIFEMAC_ETH functionality can only work with both DM_ETH_PHY and
DM_MDIO enabled (it calls one of the functions that requires both), so
express this dependency in Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
The CMD_PXE functionality can only build with CMD_TFTPBOOT enabled (or
we get undefined references to do_tftpb), so express this dependency in
Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds support for RTL8125d. Its chip version is 0x6a.
Signed-off-by: Javen Xu <javen_xu@realsil.com.cn>
[jf: add missing comma]
Signed-off-by: Jerome Forissier <jerome.forissier@arm.com>
When resolving a symlink, nfs_path points into a heap allocated buffer
which is just large enough to hold the original path with no extra
space. If the symlink target name is longer than the original
filename, the write goes beyond the end of the buffer corrupting
heap memory.
Fix this by ensuring nfs_path always points to a buffer large enough
to accommodate the resolved symlink path.
Fixes: 230cf3bc27 ("net: lwip: nfs: Port the NFS code to work with lwIP")
Signed-off-by: Pranav Tilak <pranav.vinaytilak@amd.com>
Acked-by: Jerome Forissier <jerome.forissier@arm.com>
Reviewed-by: Jerome Forissier <jerome.forissier@arm.com>
Functionally, both networking stacks require DM_ETH. This is because
they both also require some networking devices to be enabled. Express
this more correctly by having both NET and NET_LWIP select NETDEVICES.
In turn NETDEVICES no longer depends on NET or NET_LWIP as it's not
prompted anymore.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jerome Forissier <jerome.forissier@arm.com>
- Add a call to phy_reset() in ksz9031_config() to ensure the PHY is
properly reset during initialization.
- This clears the power-down bit and ensures the PHY recovers correctly
after Linux reboot.
Tested on Agilex5 hardware with KSZ90X1 PHY.
Signed-off-by: Boon Khai Ng <boon.khai.ng@altera.com>
- Move DMA software reset and pad calibration in xgmac_start() to occur
after the PHY is initialized and connected.
- This ensures the PHY is ready before performing these operations,
which is necessary for proper recovery after reboot.
This change fixes issues where the PHY did not recover from power-down
state after a Linux reboot, for the board using Micrel KSZ90x1 PHY.
Signed-off-by: Boon Khai Ng <boon.khai.ng@altera.com>
As exposed by "make randconfig", we have a few dependency issues with
some network drivers:
- Both HIFEMAC_ETH and HIGMACV300_ETH functionally require both DM and
OF_CONTROL. Further, HIFEMAC_ETH needs DM_CLK not just CLK to be
selected.
- BNXT_ETH deals with it's PCI requirement in a backwards way. The
symbol PCI_INIT_R is board specific, PCI alone is required to build.
Signed-off-by: Tom Rini <trini@konsulko.com>
Airoha PCS driver depends on ARCH_AIROHA, so it should not be built
by allyesconfig configuration.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Airoha switch mdio maybe used not only by GDM1, but also by other GDM
ports (ex: as21xxx phy connected to GDM2 port). So it's better probe
airoha switch mdio a bit early in the airoha_eth_probe() code.
Also remove useless eth_phy_set_mdio_bus() call and related code.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
This allows us to expose MMC devices to the host for easy
flashing via USB.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Primoz Fiser <primoz.fiser@norik.com>
