The MT798x series SoCs have IES regiter definitions. They should
belong to the pinctrl v1 revision.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
The following clocks have been added for MT8195 SoC:
apmixedsys, topckgen, infracfg
These clocks driver are based on the ones present in the kernel:
drivers/clk/mediatek/clk-mt8195-*
Signed-off-by: Chris-QJ Chen <chris-qj.chen@mediatek.com>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
This adds basic support for MediaTek MT8195 SoC.
Add watchdog support by adding upstream compatible string.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Julien Stephan <jstephan@baylibre.com> says:
I recently submitted the clock driver for MT8188. I naively submitted a
driver that was ported from the kernel driver, and mostly work to boot a
kernel.
Recently David Lechner, added support for the clk dump command for
Mediatek clock drivers, so I used it to check the MT8188 and found
several issues fixed on this series:
- removed topckgen_cg, gates are now part of topckgen
- fixed several parents clocks
- added missing fixed clocks
While at it, I also refactored a bit the driver to improve readability,
and future additions to it.
Link: https://lore.kernel.org/r/20260202-mt8188-fix-clock-v2-0-b39bddfcac66@baylibre.com
Refactor some part of the driver to improve readability and future
additions:
- use CLK_TOP_NR_CLK for added clocks
- rename the id map to make it more clear that the map applies to top
clocks only
- refactor the id map to improve readability
- xtal2_rate is only used for PLL clocks, so only the apmixedsys clock
tree needs it. Remove it elsewhere.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Remove the separate topckgen-cg driver for handling clock gates in the
topckgen address space.
Commit 8aeeeff50d ("clk: mediatek: allow gates in topckgen drivers")
added support for gates in topckgen driver.
This commit fixes MT8188 driver, the same way commit ba207d7f54 ("clk:
mediatek: mt8365: remove separate topckgen-cg driver") does for MT8365.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
This adds support for the MT8370 EVK board with the following
features enabled/tested: Boot, UART, Watchdog and MMC.
MT8370 is based on MT8188.
Reviewed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Add a CONFIG_MTK_MEM_MAP_DDR_BASE_PHY variable to specify the DDR base
physical address for the Mediatek ARMv8 memory map. This will be used
by MT8196 in the future which has a different DDR base address than
other Mediatek SoCs.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Consolidate all mem_map definitions for MediaTek ARMv8 platforms into a
single file. The size of the DDR and MMIO regions can vary, so Kconfig
options are added to configure them by target.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Move the mt8365_evk and mt8390_evk MAINTAINERS files to a common
MAINTAINERS file. We will be deleting the board-specific directories
soon but we need to keep the MAINTAINERS for the defconfig entries.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Make the mtk_pll_early_init() function static in several files. It is
only used within those files, so there is no need to have it in the
global namespace.
Reviewed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Add a weak default implementation of mtk_soc_early_init() in spl.c to
avoid having to define it in every SoC init.c file that does not need
any additional early initialization.
The init.h header file is no longer needed in this case and is removed.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Raymond Mao <raymondmaoca@gmail.com> says:
From: Raymond Mao <raymond.mao@riscstar.com>
This series finish the last missing puzzle of required SMBIOS types by:
1) Fixing duplicated handles when multiple instances exist in one type;
2) Implementing the rest of required types 9/16/17/19;
3) Adding version control when printing properties for all types.
Type 9/16/17/19 are generally DT-based, the idea is to write these tables
using a hybrid approach:
Explicit DT definitions under existing '/smbios/smbios' take precedence,
with fallback to scan and interpret values from the entire DT.
Moreover, all below APIs:
smbios_get_val_si()
smbios_get_u64_si()
smbios_add_prop_si()
are on top of sysinfo, thus allow vendors to get values from other
subsystems by implementing their own sysinfo driver if needed.
Link: https://lore.kernel.org/r/20260213225254.2544596-1-raymondmaoca@gmail.com
By checking the payload length, we can know the version of the spec and
skip the ones which are not expected to exist.
Signed-off-by: Raymond Mao <raymondmaoca@gmail.com>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This commit implements SMBIOS Type 19 (Memory Array Mapped Address)
generation with a hybrid approach supporting both:
1. Explicit definition via Device Tree 'smbios' node:
Child node under '/smbios/smbios/memory-array-mapped-address' will be
used to populate as individual Type 19 structure directly.
- Properties follow SMBIOS field names with lowercase letters and
hyphen-separated words (e.g., 'starting-address', 'ending-address',
'partition-width', etc.).
- This method supports precise platform-defined overrides and system
descriptions.
2. Fallback to automatic DT-based discovery:
If child node under '/smbios/smbios/memory-array-mapped-address' does
not exist, the implementation will:
- Scan all top-level 'memory@' nodes to populate Type 19 structure with
inferred size and location data.
- Scan nodes named or marked as 'memory-controller' and parse
associated 'dimm@' subnodes (if present) to extract DIMM sizes and
map them accordingly.
This dual-mode support enables flexible firmware SMBIOS reporting while
aligning with spec-compliant naming and runtime-detected memory topology.
Type 19 support is under GENERATE_SMBIOS_TABLE_VERBOSE to avoid
increasing rom size for those platforms which only require basic SMBIOS
support.
Signed-off-by: Raymond Mao <raymondmaoca@gmail.com>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This commit implements SMBIOS Type 17 (Memory Device) generation with a
hybrid approach supporting both:
1. Explicit definition via Device Tree 'smbios' node:
Child node under '/smbios/smbios/memory-device' will be used to
populate as individual Type 17 structure directly.
- Properties follow SMBIOS field names with lowercase letters and
hyphen-separated words (e.g., 'physical-memory-array-handle',
' memory-error-information-handle', 'configured-memory-speed', etc.).
- This method supports precise platform-defined overrides and system
descriptions.
2. Fallback to automatic DT-based discovery:
If child node under '/smbios/smbios/memory-device' does not exist,
the implementation will:
- Scan all top-level 'memory@' nodes to populate Type 17 structure with
inferred size and location data.
- Scan nodes named or marked as 'memory-controller' and parse
associated 'dimm@' subnodes (if present) to extract DIMM sizes and
map them accordingly.
This dual-mode support enables flexible firmware SMBIOS reporting while
aligning with spec-compliant naming and runtime-detected memory topology.
Type 17 support is under GENERATE_SMBIOS_TABLE_VERBOSE to avoid
increasing rom size for those platforms which only require basic SMBIOS
support.
Signed-off-by: Raymond Mao <raymondmaoca@gmail.com>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This commit implements SMBIOS Type 16 (Physical Memory Array)
generation with a hybrid approach supporting both:
1. Explicit definition via Device Tree 'smbios' node:
Child node under '/smbios/smbios/memory-array' will be used to
populate as individual Type 16 structure directly.
- Properties follow SMBIOS field names with lowercase letters and
hyphen-separated words (e.g., 'memory-error-correction',
'maximum-capacity', 'extended-maximum-capacity', etc.).
- This method supports precise platform-defined overrides and system
descriptions.
2. Fallback to automatic DT-based discovery:
If child node under '/smbios/smbios/memory-array' does not exist,
the implementation will:
- Scan all top-level 'memory@' nodes to populate Type 16 structure with
inferred size and location data.
- Scan nodes named or marked as 'memory-controller' and parse
associated 'dimm@' subnodes (if present) to extract DIMM sizes and
map them accordingly.
This dual-mode support enables flexible firmware SMBIOS reporting while
aligning with spec-compliant naming and runtime-detected memory topology.
Type 16 support is under GENERATE_SMBIOS_TABLE_VERBOSE to avoid
increasing rom size for those platforms which only require basic SMBIOS
support.
Signed-off-by: Raymond Mao <raymondmaoca@gmail.com>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This commit introduces support for generating SMBIOS Type 9 (System Slot)
tables using a hybrid approach:
1. Explicit Device Tree definitions:
Child node under '/smbios/smbios/system-slot' will be interpreted as
individual slot definitions.
- Each child represents a slot (e.g., isa, pcmcia, etc.).
- Properties follow the SMBIOS specification using lowercase
hyphen-separated names such as 'slot-type', 'slot-id',
'segment-group-number', 'bus-number', 'slot-information', etc.
- This approach allows full customization of each system slot and is
especially suitable for platforms with well-defined slot topology.
2. Automatic detection fallback:
If child node under '/smbios/smbios/system-slot' does not exist, the
implementation will scan the entire device tree for nodes whose
'device_type' matches known slot-related types ("pci", "isa", "pcmcia",
etc.).
- When a match is found, default values or heuristics are applied to
populate to the System Slot table.
- This mode is useful for platforms that lack explicit SMBIOS nodes
but still expose slot topology via standard DT conventions.
Together, two approaches ensure that SMBIOS Type 9 entries are available
whether explicitly described or automatically derived.
Signed-off-by: Raymond Mao <raymondmaoca@gmail.com>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Some smbios types can have multiple instances (e.g. Type 7, 9, 16, 17,
19), thus the 'handle' argument should be a pointer so that the value
can be accumulated when writing all the instances.
This also fix the observed duplicated Type 7 handles.
Fixes: bcf456dd36 ("smbios: add detailed smbios information")
Signed-off-by: Raymond Mao <raymondmaoca@gmail.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Peng Fan (OSS) <peng.fan@oss.nxp.com> says:
This patch set primarily removes unused DECLARE_GLOBAL_DATA_PTR
instances.
Many files declare DECLARE_GLOBAL_DATA_PTR and include
asm/global_data.h even though gd is never used. In these cases,
asm/global_data.h is effectively treated as a proxy header, which is
not a good practice.
Following the Include What You Use principle, files should include
only the headers they actually depend on, rather than relying on
global_data.h indirectly. This approach is also adopted in Linux kernel
[1].
The first few patches are prepartion to avoid building break after
remove the including of global_data.h.
A script is for filtering the files:
list=`find . -name "*.[ch]"`
for source in ${list}
do
result=`sed -n '/DECLARE_GLOBAL_DATA_PTR/p' ${source}`
if [ "${result}" == "DECLARE_GLOBAL_DATA_PTR;" ]; then
echo "Found in ${source}"
result=`sed -n '/\<gd\>/p' ${source}`
result2=`sed -n '/\<gd_/p' ${source}`
result3=`sed -n '/\<gd->/p' ${source}`
if [ "${result}" == "" ] && [ "${result2}" == "" ] && [ "${result3}" == "" ];then
echo "Cleanup ${source}"
sed -i '/DECLARE_GLOBAL_DATA_PTR/{N;/\n[[:space:]]*$/d;s/.*\n//;}' ${source}
sed -i '/DECLARE_GLOBAL_DATA_PTR/d' ${source}
sed -i '/global_data.h/d' ${source}
git add ${source}
fi
fi
done
[1] https://lpc.events/event/17/contributions/1620/attachments/1228/2520/Linux%20Kernel%20Header%20Optimization.pdf
CI: https://github.com/u-boot/u-boot/pull/865
Link: https://lore.kernel.org/r/20260209-cleanup-v2-0-73a3a84ddbdb@nxp.com
Remove DECLARE_GLOBAL_DATA_PTR from files where gd is not used, and
drop the unnecessary inclusion of asm/global_data.h.
Headers should be included directly by the files that need them,
rather than indirectly via global_data.h.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com> #STMicroelectronics boards and STM32MP1 ram test driver
Tested-by: Anshul Dalal <anshuld@ti.com> #TI boards
Acked-by: Yao Zi <me@ziyao.cc> #TH1520
Signed-off-by: Peng Fan <peng.fan@nxp.com>
struct udevice and u32 are used in this file. Add missing header to avoid
building break after asm/global_data.h is removed from this file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
struct bd_info is defined in asm-generic/u-boot.h. Include it to avoid
building error after asm/global_data.h are removed from this file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
struct fdt_resource, u32 and bool types are used in this header, add
missing header files following "include what you use".
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There is no user of gd, drop the usage of DECLARE_GLOBAL_DATA_PTR and
the including of "asm/global_data.h". Include config.h to avoid
build error.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There is no user of 'gd', so drop the usage of DECLARE_GLOBAL_DATA_PTR
and the including of 'asm/global_data.h'. Also include correct headers
to avoid build error.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
No gd users, so remove DECLARE_GLOBAL_DATA_PTR and the including of
"asm/global_data.h". And include "asm/arch-tegra/tegra.h" to avoid
build error.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Include linux/types.h and asm-generic/u-boot.h. Missing the two header
files will cause building error after cleaning up usage of
asm/global_data.h.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
snprintf is used, need to include vsprintf.h. Otherwise there will
be build error after asm/global_data.h is removed.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
CI: https://source.denx.de/u-boot/custodians/u-boot-tpm/-/pipelines/29283
An update on AB subsystem allowing multiple FWU metadata
storage drivers to be selected simultaneously instead of
being mutually exclusive. The board can then select the
appropriate driver at runtime based on the devicetree
description.
Pull request efi-next-2026-02-15
CI: https://source.denx.de/u-boot/custodians/u-boot-efi/-/jobs/1380382
UEFI:
* Add MBR support to EFI_PARTITION_INFO_PROTOCOL
* disk: part_dos: Move header to the main include directory
* disk: part_dos: Align dos_partition_t with struct partition
* disk: part_efi: Remove redundant struct partition definition
* disk: part_dos: Document part_get_info_extended() helper function
* disk: part_dos: Refactor to allow retrieving raw MBR partition data
* efi_loader: disk: Extend EFI_PARTITION_INFO_PROTOCOL to support MBR
* efi_selftest: Enhance MBR test for PARTITION_INFO_PROTOCOL
* Prepare for supporting more stores (e.g. SPI-flash) for EFI variables.
* efi_var: Unify read/write access helper function
* efi_loader: Setup default location for UEFI Variables storing
* efi_var_file: refactor to move buffer functions
EFI_VARIABLE_FILE_STORE is only available when FAT_WRITE is enabled but
that's not valid for all platforms and dependency should be covered.
Also Kconfig behavior is that if default option is not valid then Kconfig
selects the first presented valid option instead hence it is better to
record EFI_VARIABLE_NO_STORE as safe default option.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
efi_var_to/from_file() suggest method where variables are placed. But there
is no reason for it and generic name can be used to wire also different
locations for variables.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on AML-S905D3-CC
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Currently efi_var_file.c has functions to store/read
EFI variables to/from memory buffer. These functions
can be used with other EFI variable stores so move
them out to efi_var_common.c
Signed-off-by: Shantur Rathore <i@shantur.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on AML-S905D3-CC
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The EFI_PARTITION_INFO_PROTOCOL test was added before the protocol fully
supported MBR partitions. As a result, it lacked specific checks for the
content of the raw MBR partition record.
Now that MBR support has been implemented, enhance the selftest to provide
coverage for the MBR entries too.
This verifies that the protocol correctly reads and exposes MBR partition
records and prevents this functionality to regress due future changes.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Shiji YangandTom Rini
Chris-QJ ChenandTom Rini
Julien StephanandTom Rini
David LechnerandTom Rini
Raymond MaoandTom Rini
Peng FanandTom Rini
Michal SimekandHeinrich Schuchardt
Shantur RathoreandHeinrich Schuchardt
Javier Martinez CanillasandHeinrich Schuchardt