In case DM drivers probe earlier than board clock setup is done
init of basic clocks should be done in CAR driver probe as well.
Add it to avoid possible clock related problems.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Return PLL id into struct clk if PLL is parsed from device
tree instead of throwing an error. Allow requesting PLL
clock rate via get_rate op.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
On 64bit systems the timer value might be truncated to a 32bit value
causing malfunctions. For example on ARM the timer might start from 0
again only after a cold reset. The 32bit overflow occurs after a bit
more than 49 days (1000 Hz counter) so booting after that time may lead
to a surprise because the board might become stuck requiring a cold
reset.
Signed-off-by: Ronald Wahl <ronald.wahl@legrand.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
buf was used as destination and as parameter to sprintf
which triggers an undefined behaviour.
This commit removes this usage of sprintf and uses strcat
to append strings to buf variable.
Signed-off-by: Francois Berder <fberder@outlook.fr>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Without this patch, there will be error indicating that
"Cannot use 64 bit addresses with SDMA", and the booting
process will stuck.
please see full boot log below
U-Boot 2022.04-g18185931 (Sep 11 2024 - 13:15:30 +0800)
SoC: LS1028AE Rev1.0 (0x870b0010)
Clock Configuration:
CPU0(A72):1500 MHz CPU1(A72):1500 MHz
Bus: 400 MHz DDR: 1600 MT/s
Reset Configuration Word (RCW):
00000000: 3c004010 00000030 00000000 00000000
00000010: 00000000 018f0000 0030c000 00000000
00000020: 020031a0 00002580 00000000 00003296
00000030: 00000000 00000010 00000000 00000000
00000040: 00000000 00000000 00000000 00000000
00000050: 00000000 00000000 00000000 00000000
00000060: 00000000 00000000 200e705a 00000000
00000070: bb580000 00000000
Model: LS1028A RDB Board
Board: LS1028AE Rev1.0-RDB, Version: C, boot from SD
FPGA: v8 (RDB)
SERDES1 Reference : Clock1 = 100.00MHz Clock2 = 100.00MHz
DRAM: 3.9 GiB
DDR 3.9 GiB (DDR4, 32-bit, CL=11, ECC on)
Using SERDES1 Protocol: 47960 (0xbb58)
PCIe1: pcie@3400000 Root Complex: no link
PCIe2: pcie@3500000 Root Complex: x1 gen2
Core: 45 devices, 22 uclasses, devicetree: separate
WDT: Started watchdog@c000000 with servicing (60s timeout)
WDT: Started watchdog@c010000 with servicing (60s timeout)
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment
EEPROM: Invalid ID (ff ff ff ff)
In: serial
Out: serial
Err: serial
SEC0: RNG instantiated
Net:
Warning: enetc-0 (eth0) using random MAC address - d2:9b:a5:37:7b:b5
eth0: enetc-0
Warning: enetc-2 (eth1) using random MAC address - ca:57:11:de:de:cb
, eth1: enetc-2, eth2: swp0, eth3: swp1, eth4: swp2, eth5: swp3
Hit any key to stop autoboot: 0
Trying load HDP firmware from SD..
switch to partitions #0, OK
mmc0 is current device
Device: FSL_SDHC
Manufacturer ID: 9f
OEM: 5449
Name: SD32G
Bus Speed: 50000000
Mode: SD High Speed (50MHz)
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 28.9 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
MMC read: dev # 0, block # 18944, count 512 ... 512 blocks read: OK
Loading hdp firmware from 0x00000000a0000000 offset 0x0000000000002000
Loading hdp firmware Complete
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
** Unable to read file / **
Failed to load '/'
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
Scanning disk mmc@2140000.blk...
Scanning disk mmc@2150000.blk...
Found 7 disks
ERROR: invalid device tree
Found EFI removable media binary efi/boot/bootaa64.efi
981992 bytes read in 44 ms (21.3 MiB/s)
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
WARNING could not find node vivante,gc: FDT_ERR_NOTFOUND.
Booting /efi\boot\bootaa64.efi
Cannot use 64 bit addresses with SDMA
Error reading cluster
** Unable to read file /efi/boot/grubaa64.efi **
Unexpected return from initial read: Device Error, buffersize 29D790
Failed to load image ￢ : Device Error
start_image() returned Device Error
EFI LOAD FAILED: continuing...
switch to partitions #0, OK
mmc1(part 0) is current device
Scanning mmc 1:1...
** Unable to read file / **
Failed to load '/'
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
BootOrder not defined
EFI boot manager: Cannot load any image
Scanning mmc 1:2...
** Unable to read file / **
Failed to load '/'
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
BootOrder not defined
EFI boot manager: Cannot load any image
starting USB...
Bus usb@3100000: Register 200017f NbrPorts 2
Starting the controller
USB XHCI 1.00
Bus usb@3110000: Register 200017f NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus usb@3100000 for devices... 1 USB Device(s) found
scanning bus usb@3110000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Device 0: unknown device
Trying load from SD ...
switch to partitions #0, OK
mmc0 is current device
Device: FSL_SDHC
Manufacturer ID: 9f
OEM: 5449
Name: SD32G
Bus Speed: 50000000
Mode: SD High Speed (50MHz)
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 28.9 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
MMC read: dev # 0, block # 32768, count 81920 ... 81920 blocks read: OK
Wrong Image Format for bootm command
ERROR: can't get kernel image!
Signed-off-by: Wei Ming Chen <jj251510319013@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Board introductions have a feature list which isn't formatted properly
according to rST and is thus rendered incorrectly.
Fix this by adding the missing newlines in the appropriate places.
Signed-off-by: Quentin Schulz <quentin.schulz@cherry.de>
Add a blank line after title "Specification:" to
make it render correctly html.
And also remove the useless > in bash code block.
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Most Rockchip device tree related bindings are converted to YAML
and available in the U-boot /dts/upstream/Bindings/ directory.
Remove all redundant U-boot entries.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Although it has historically been different, the current standard
spelling of the neutral singular possessive pronoun is "its".
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Since commit 61ff13283c ("board: sl28: move to OF_UPSTREAM") USB0 is
broken because the former u-boot soc dtsi was setting dr_mode to "host"
but the linux device tree isn't. That is because linux fully supports
OTG but u-boot doesn't. Therefore, u-boot only ever enabled host mode
and never OTG mode. Add it to our board "-u-boot.dtsi" to fix it.
Fixes: 61ff13283c ("board: sl28: move to OF_UPSTREAM")
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Network is broken on variant 3 boards since commit 61ff13283c ("board:
sl28: move to OF_UPSTREAM") because it was removing the variant 3
handling. That is because at that time the var3 device tree was not
upstream. FWIW variant 3 is actually the same as the base variant, but
I've missed that the -u-boot.dtsi is not inlcuded in this case which
will set the ethernet alias. Now that the var3 device tree is upstream,
just re-add it to the SPL handling again.
Fixes: 61ff13283c ("board: sl28: move to OF_UPSTREAM")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Increase the malloc size to 2MiB because our FIT image exceeds the 1MiB
limit either if BL31 mode is enabled or if another device tree is added
to the image.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
We don't have a reference to the driver used by
uclass_get_device_by_driver() in stop_recovery_watchdog(). Fix it by not
calling that function if the watchdog driver isn't enabled.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The boot_fdt_add_mem_rsv_regions() function can be called twice, e.g.
first time during the board init (as a part of LMB init), and then when
booting the OS with 'booti' command:
lmb_add_region_flags
lmb_reserve_flags
boot_fdt_reserve_region
boot_fdt_add_mem_rsv_regions
^
|
+-----------------------+
| (1) | (2)
lmb_reserve_common image_setup_linux
lmb_init ...
initr_lmb do_booti
board_init_r 'booti'
That consequently leads to the attempt of reserving the same memory
areas (described in the 'reserved-memory' dts node) in LMB. The
lmb_add_region_flags() returns -EEXIST error code in such cases, but
boot_fdt_reserve_region() handles all negative error codes as a failure
to reserve fdt memory region, printing corresponding error messages,
which are essentially harmless, but misleading. For example, this is the
output of 'booti' command on E850-96 board:
=> booti $loadaddr - $fdtaddr
...
ERROR: reserving fdt memory region failed
(addr=bab00000 size=5500000 flags=2)
ERROR: reserving fdt memory region failed
(addr=f0000000 size=200000 flags=4)
...
Starting kernel ...
The mentioned false positive error messages are observed starting with
commit 1d9aa4a283 ("lmb: Fix the allocation of overlapping memory
areas with !LMB_NONE"), which removes the check for the already added
memory regions in lmb_add_region_flags(), making it return -1 for
!LMB_NONE cases. Another commit 827dee587b ("fdt: lmb: add reserved
regions as no-overwrite") changes flags used for reserving memory in
boot_fdt_add_mem_rsv_regions() from LMB_NONE to LMB_NOOVERWRITE. So
together with the patch mentioned earlier, it makes
lmb_add_region_flags() return -1 when called from
boot_fdt_reserve_region().
Since then, the different patch was implemented, returning -EEXIST error
code in described cases, which is:
lmb: Return -EEXIST in lmb_add_region_flags() if region already added
Handle -EEXIST error code as a normal (successful) case in
lmb_reserve_flags() and don't print any messages.
Fixes: 1d9aa4a283 ("lmb: Fix the allocation of overlapping memory areas with !LMB_NONE")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Michal Simek <michal.simek@amd.com>
An attempt to add the already added LMB region using
lmb_add_region_flags() ends up in lmb_addrs_overlap() check, which
eventually leads to either returning 0 if 'flags' is LMB_NONE, or -1
otherwise. It makes it impossible for the user of this function to catch
the case when the region is already added and differentiate it from
regular errors. That in turn may lead to incorrect error handling in the
caller code, like reporting misleading errors or interrupting the normal
code path where it could be treated as the normal case. An example is
boot_fdt_reserve_region() function, which might be called twice (e.g.
during board startup in initr_lmb(), and then during 'booti' command
booting the OS), thus trying to reserve exactly the same memory regions
described in the device tree twice, which produces an error message on
second call.
Return -EEXIST error code in case when the added region exists and it's
not LMB_NONE; for LMB_NONE return 0, to conform to unit tests
(specifically test_alloc_addr() in test/lib/lmb.c) and the preferred
behavior described in commit 1d9aa4a283 ("lmb: Fix the allocation of
overlapping memory areas with !LMB_NONE"). The change of
lmb_add_region_flags() return values is described in the table below:
Return case Pre-1d9 1d9 New
-----------------------------------------------------------
Added successfully 0 0 0
Failed to add -1 -1 -1
Already added, flags == LMB_NONE 0 0 0
Already added, flags != LMB_NONE 0 -1 -EEXIST
Rework all affected functions and their documentation. Also fix the
corresponding unit test which checks reserving the same region with the
same flags to account for the changed return value.
No functional change is intended (by this patch itself).
Fixes: 1d9aa4a283 ("lmb: Fix the allocation of overlapping memory areas with !LMB_NONE")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Michal Simek <michal.simek@amd.com>
Since RPI works well using EFI and has no size limitations with regards
to U-Boot, add the needed structures to support capsule updates.
While at it update the most commonly used defconfigs and include capsule
support and U-Boot commands needed by EFI
Tested-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
For a lot of usecases, such as display, camera, media
the Raspberry Pi needs a lot more CMA than distros
configure as default so we should pass this parameter
through so things work as expected. Fix a spelling
mistake while we're at it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Matthias Brugger <mbrugger@suse.com>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Comment changes only, no functional change.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Kconfig strings and comment changes only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The correct spelling is R-Car, including the dash, update the usage.
Comment change only, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The U-Boot is currently not capable of handling ethernet-phy-ieee802.3-c45
PHYs correctly, and also does not handle MDIO bus wide reset-gpios property.
Until proper C45 PHY support lands in U-Boot, disable AVB1/AVB2 interfaces.
This only disables the two MACs with 88Q2110/88Q2112 100/1000BASE-T1 PHYs
on ethenet sub-board, the main board AVB0 ethernet is unaffected.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In rzg2l_pinconf_set(), there are no new variables defined in the case
statement for PIN_CONFIG_INPUT_ENABLE so no additional scope is needed.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
On the RZ/G2L SoC family, the direction of the Ethernet TXC/TX_CLK
signal is selectable to support an Ethernet PHY operating in either MII
or RGMII mode. By default, the signal is configured as an input and MII
mode is supported. The ETH_MODE register can be modified to configure
this signal as an output to support RGMII mode.
As this signal is be default an input, and can optionally be switched to
an output, it maps neatly onto an `output-enable` property in the device
tree.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Svyatoslav RyhelandTom Rini
Ronald WahlandJaehoon Chung
Francois BerderandPeng Fan
Wei Ming ChenandPeng Fan
Leonard AnderweitandHeinrich Schuchardt
Jerome ForissierandHeinrich Schuchardt
Quentin SchulzandHeinrich Schuchardt
Simon GlassandHeinrich Schuchardt
Andy YanandHeinrich Schuchardt
Johan JonkerandHeinrich Schuchardt
J. NeuschäferandHeinrich Schuchardt
Michael WalleandPeng Fan
Sam ProtsenkoandTom Rini
Roger QuadrosandTom Rini
Ilias ApalodimasandPeter Robinson
Michal Simek
Marek Vasut
Venkatesh Yadav AbbarapuandMarek Vasut
Paul BarkerandMarek Vasut