Use macro to represent the RL and WL setting to ensure the PHY and
controller setting are aligned.
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Adjust the following settings to get better timing and signal quality.
1. write DQS/DQ delay
- 1e6e2304[0]
- 1e6e2304[15:8]
2. read DQS/DQ delay
- 0x1e6e0298[0]
- 0x1e6e0298[15:8]
3. CLK/CA timing
- 0x1e6e01a8[31]
4. Read and write termination
- change RTT_ROM from 40 ohm to 48 ohm (MR1[10:8])
- change RTT_PARK from disable to 48 ohm (MR5[8:6])
- change RTT_WR from 120 ohm to disable (MR2[11:9])
- change PHY ODT from 40 ohm to 80 ohm (0x1e6e0130[10:8])
Note1: Both DDR-PHY and DDR controller have their own registers for DDR4
Mode Registers (MR0~MR6). This patch introduces macros to synchronize
the MR value on both sides.
Note2: the waveform meansurement can be found in item #21 of Aspeed
AST26x0 Application note (AP note).
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
The condition "~data" in the if-statement is a typo. The original
intention is to poll if SDRAM_PHYCTRL0_INIT bit equals to 0. So use
"data == 0" for instead.
Besides, the bit[1] of "phy_status" register is hardwired to
SDRAM_PHYCTRL0_INIT (with inverse logic). Since SDRAM_PHYCTRL0_INIT has
already done, remove the unnecessary checking of phy_status[1].
Fixes: fde9314346 ("ram: aspeed: Add AST2600 DRAM control support")
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
The clock delay of the RMII/RGMII interface is controlled by SCU340~35C.
These values are obtained by measurement and experiments so we simply
use macro to define them.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
There are 4 MDIO bus controllers in AST2600 SOC. Each of them can
connect to one or more PHY chips and is flexible to work with the 4 MAC
devices in AST2600. On AST2600 EVB, MDIO 0,1,2,3 connect to the PHY
chips used by MAC 0,1,2,3 respectively.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add support of the MAC controller of Aspeed AST2600 SOC. The MAC
controller is the same with AST2500, except it has stand-alone MDIO
hardware block.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add support for DM_MDIO to connect to PHY. For the systems that have a
stand-alone MDIO hardware block, enable CONFIG_DM_MDIO to use driver
model for MDIO devices.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
AST2600 supports DDR4 SDRAM with maximum speed DDR4-1600.
The DDR4 DRAM types including 128MbX16 (2Gb), 256MbX16 (4Gb),
512MbX16 (8Gb), 1GbX16 (16Gb), and 1GbX8 TwinDie (16Gb) are supported.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
the aspeed ddr sdram controller needs to know if the memory chip mounted on
the board is dual x8 die or not. Or it may get the wrong size of the
memory space.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
to improve the maintainability. It is more easier to modify and add
configurations of the driver in the centralized ram driver directory.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Dylan HungandTom Rini
