Use regulator_set_enable_if_allowed() api instead of regulator_set_enable()
while disabling vbus supply. This way the driver doesn't see an error
when it disable an always-on regulator for VBUS.
This patch is needed for STM32MP157C-DK2 board when the regulator
v3v3: buck4 used as the phy vbus supply in kernel device tree
is always on with the next hack for low power use-case:
&usbphyc_port0 {
...
/*
* Hack to keep hub active until all connected devices are suspended
* otherwise the hub will be powered off as soon as the v3v3 is disabled
* and it can disturb connected devices.
*/
connector {
compatible = "usb-a-connector";
vbus-supply = <&v3v3>;
};
};
Without this patch and the previous update in DT the command
"usb stop" failed and the next command "usb start" cause a crash.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Merge tag 'u-boot-nand-20221211' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash
- cmd: nand: Extend nand info to print ecc information
- rawnand: omap_gpmc: driver model support (the first patches of the series)
- mtd: nand: make Samsung SLC NAND usable again
- cmd: mtd: check if a block has to be skipped or erased
- spl: spl_legacy: fix invalid offset in SPL_COPY_PAYLOAD_ONLY
Upstream linux commit 69fc01296c9281
commit a1286a1fc4 ("mtd: nand: Move Samsung specific init/detection
logic in nand_samsung.c") introduced a regression for Samsung SLC NAND
chips. Prior to this commit chip->bits_per_cell was initialized by calling
nand_get_bits_per_cell() before using nand_is_slc().
With the offending commit this call is skipped, leaving
chip->bits_per_cell cleared to zero when the manufacturer specific
'.detect' function calls nand_is_slc() which in turn interprets
bits_per_cell != 1 as indication for an MLC chip.
The effect is that e.g. a K9F1G08U0F NAND chip is falsely detected as
MLC NAND with 4KiB page size rather than SLC with 2KiB page size.
Add a call to nand_get_bits_per_cell() before calling the .detect hook
function in nand_manufacturer_detect(), so that the nand_is_slc()
calls in the manufacturer specific code will return correct results.
Reported-by: Marcin Gołaś <marcingol30@gmail.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221021060536.11747-1-michael@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
- Drop MMCI interrupt-names in STM32H743, STM32MP15 and STM322MP13 DT
DHSOM:
- Enable assorted ST specific commands
- Add version variable
- Add boot counter
STM32MP13:
- Add sdmmc cd-gpios for STM32MP135F-DK
- Add clock & reset support
STM32 ADC:
- Split channel init into several routines
- Add support of generic channels binding
Prevent access to arbitrary memory locations in gen_ndis_set_resp
via manipulation of buf->InformationBufferOffset. Original
implementation permits manipulation of InformationBufferOffset to
exploit OID_GEN_CURRENT_PACKET_FILTER to set arbitrary memory contents
within a 32byte offset as the devices packet filter. The packet filter
value may be next retrieved using gen_ndis_query_resp so it is possible
to extract specific memory regions two bytes a time.
The rndis_query_response was not modified as neither the buffer offset
nor length passed to gen_ndis_query_resp is used.
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Define stub for dfu_*_virt function in SPL, because
CONFIG_SPL_DFU_VIRT is not defined.
This patch avoids compilation issue in dfu_fill_entity() when
CONFIG_SPL_DFU is activated because the dfu_fill_entity_virt()
function is not available.
Fixes: ec44cace4b ("dfu: add DFU virtual backend")
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
- Kautuk's semihosting patch:
move semihosting library from arm directory to common place and add
RISC-V support
- Zong's Kconfig patch:
use "imply" instead of "select" to allow user to decide if
SPL_SEPARATE_BSS should be selected
Second set of u-boot-at91 fixes for the 2023.01 cycle:
This is a single tiny fix that allows the correct name for one pin on
sama7g5 device. People with DT coming from Linux will have build errors
without this if they add NAND device.
Use imply instead of select, then it can still be disabled by
board-specific defconfig, or be set to n manually.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
When we enable CONFIG_SPL and CONFIG_SPL_SEMIHOSTING then the code
in common/spl/spl_semihosting.c tries to use the
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME string which remains undeclared
unless SPL_FS_EXT4 || SPL_FS_FAT || SPL_FS_SQUASHFS are configured.
Add a dependency of SPL_SEMIHOSTING in the depends for
SPL_FS_LOAD_PAYLOAD_NAME so that the code compiles fine.
Signed-off-by: Kautuk Consul <kconsul@ventanamicro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
We factor out the arch-independent parts of the ARM semihosting
implementation as a common library so that it can be shared
with RISC-V.
Signed-off-by: Kautuk Consul <kconsul@ventanamicro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Enable watchdog timer on the DHSOM by default, both in U-Boot proper and
in SPL. This can be used in combination with boot counter by either SPL
or U-Boot proper to boot either copy of system software, e.g. in case of
full A/B update strategy.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Increment the boot counter already in U-Boot SPL instead of incrementing
it only later in U-Boot proper. This can be used by SPL to boot either of
two U-Boot copies and improve redundancy of software on the platform, e.g.
in case of full A/B update strategy.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Enable the stm32prog, stm32key, stboard commands on DHSOM.
Those can be used e.g. to implement verified boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Enable insertion of version variable into U-Boot environment on DHSOM,
to make it possible to check U-Boot version e.g. in U-Boot scripts.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add boot counter to STM32MP15xx DHSOM. This aligns the software with
other upstream DHSOM products which already do enable boot counter.
The boot counter on STM32MP15xx is placed in the TAMP block TAMP_BKPxR
register 19, right past register 17 and 18 used for CM4 resource table
and state by the Linux kernel. The TAMP_BKPxR register block is used
because its contents survives warm reset, but not cold reset.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Split stm32_adc_chan_of_init channel initialization function into
several routines to increase readability and prepare channel
generic binding handling.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
STM32MP13 RCC driver uses Common Clock Framework and also a
'clk-stm32-core' API. Then STM32MPx RCC driver will contain only data
configuration (gates, mux, dividers and the way to check security)
or some specific clocks.
This API will be used by all new other generations of ST Socs.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
To quote the author:
This patch set adds basic IPv6 support to U-boot.
It is based on Chris's Packham patches
(https://lists.denx.de/pipermail/u-boot/2017-January/279366.html)
Chris's patches were taken as base. There were efforts to launch it on
HiFive SiFive Unmatched board but the board didn't work well. The code was
refactored, fixed some bugs as CRC for little-endian, some parts were implemented in
our own way, something was taken from Linux. Finally we did manual tests and the
board worked well.
Testing was done on HiFive SiFive Unmatched board (RISC-V)
Add a test that checks generated Solicited Node Multicast Address from our
ipv6 address. Use in sandbox
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a test to check convertation from char* to struct in6_addr.
Use in sandbox
Series-changes: 3
- Fixed tests to use length param in string_to_ip6()
Series-changes: 5
- Add test under #ifdef
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement ping6 command to ping hosts using IPv6. It works the same way as
an ordinary ping command. There is no ICMP request so it is not possible
to ping our host. This patch adds options in Kconfig and Makefile to
build ping6 command.
Series-changes: 3
- Added structures and functions descriptions
- Added to ping6_receive() return value instead of void
Series-changes: 4
- Fixed structures and functions description style
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The command tftpboot uses IPv4 by default. Add the possibility to use IPv6
instead. If an address in the command is an IPv6 address it will use IPv6
to boot or if there is a suffix -ipv6 in the end of the command it also
force using IPv6. All other tftpboot features and parameters are left
the same.
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
