Increase reset assert time for TI SGMII PHY on KR260 CC starting
6.1 kernel. This PHY does not come out of reset with the existing
100us pulse width as per testing on multiple carrier cards. The reset
is driven via a PCA9570 I2C expander. The expander driver was updated
to an upstream version in 6.1 where gpio_chip _set was optimized.
Delays in earlier kernels may have masked this issue. This is a safe
workaround value for assert pulse width before the discussions are
resolved with TI.
Signed-off-by: Harini Katakam <harini.katakam@amd.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/8fb9f17d43a43ef504c9f29006cd686cce8ac98b.1688992653.git.michal.simek@amd.com
Enable flash reset functionality for Versal NET platform.
In cadence_qspi.c there is weak function defined for reset, hence remove
the check for config, so that it will work for Versal and Versal NET
platforms.
Add register defines in Versal NET hardware.h for mini U-Boot flash
reset.
Add read_delay initialization for Versal NET also.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614120452.21019-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Currently xspi0 is used for all spi boot modes, it means it will use "sf
probe 0 0 0" for all spi's irrespective of which node it is wired.
Get boot sequence from dev_seq() and update boot command for xspi
dynamically.
As a result bootcmd for spi is updated as below when two instances of spi
are present in DT node.
bootcmd_xspi0=devnum_xspi=0; run xspi_boot
bootcmd_xspi1=devnum_xspi=1; run xspi_boot
xspi_boot=sf probe $devnum_xspi:0 0 0 && sf read $scriptaddr
$script_offset_f $script_size_f && echo XSPI: Trying to boot script at
${scriptaddr} && source ${scriptaddr}; echo XSPI: SCRIPT FAILED:
continuing...;
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614093058.30438-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
It is not uncommon for some of the QEMU-based jobs to fail not because
of a code issue but rather because of a timing issue or similar problem
that is out of our control. Make use of the keywords that Azure and
GitLab provide so that we will automatically re-run these when they fail
2 times. If they fail that often it is likely we have found a real issue
to investigate.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The job to build all imx8 and imx9 platforms is currently close to, or
sometimes exceeding the allowed build time. Exclude some platforms that
are already being built under their vendor-specific job as well to
reduce the time.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently the 64bit "rk" job is close to and sometimes goes over the job
time limit. Let us rework this in to one job for "rk" and "rv" (which
are the SoC prefixes) jobs which include or exclude "rockchip" the board
vendor. This gives us two jobs of similar numbers of platforms to build
now instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Back in the day we relied a lot on Synopsys own build of the GNU tools
for ARC processors, but since then we worked hard on getting all our changes
upstream and for a couple of years now we have ARCompact (AKA ARCv1)
and ARCv2 processors supported very well in upstream GCC, Binutils, GDB etc.
And so there's no need to use Synopsys forks any longer, thus we remove
all the references to that form and use upstream components as majority
of other architectures in U-Boot.
Thanks to Tom for pointing to that left-over!
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When building qemu, all required submodules (of which we need more than
just dtc) are handled automatically. Currently trying to init the
submodule the way we do results in a git failure.
Reported-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With gcc-13.1 we get a warning about enum vs int here, so correct the
declaration to match the implementation.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With gcc-13.1 we get a warning about enum vs int here, so correct the
declaration to match the implementation.
Signed-off-by: Tom Rini <trini@konsulko.com>
When building with gcc-13.1 we see that the prototype for
cvmx_pko3_sq_config_children does not match the declaration. Make these
match and correct a typo in the function's version of the docs that the
prototype did not have, as part of keeping those in-sync.
Signed-off-by: Tom Rini <trini@konsulko.com>
Pull request efi-2023-10-rc1-2
UEFI:
* test: avoid function name 'setup' in capsule tests to not treat it as
a fixture
* ensure that device paths for USB block devices are unique
* enable having multiple EFI_LOADER block devices
* use InstallMultipleProtocolInterfaces() in TCG protocol implementation to
increase UEFI compliance
On devices with multiple USB mass storage devices errors like
Path /../USB(0x0,0x0)/USB(0x1,0x0)/Ctrl(0x0)
already installed.
are seen. This is due to creating non-unique device paths. To uniquely
identify devices we must provide path nodes for all devices on the path
from the root device.
Add support for generating device path nodes for all uclasses.
Reported-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Do not assume that the preceding device path contains a single VenHW node.
Instead use the return value of dp_fill() which provides the address of the
next node.
Fixes: 23ad52fff4 ("efi_loader: device_path: support Sandbox's "host" devices")
Fixes: 19ecced71c ("efi_loader: device path for virtio block devices")
Fixes: 272ec6b453 ("efi_loader: device_path: support blkmap devices")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
pytest 7.3.2 treats the function name 'setup' as a fixture [1].
This leads to errors like:
TypeError: setup() missing 2 required positional arguments:
'disk_img' and 'osindications'
Rename setup() to capsule_setup().
[1] How to run tests written for nose
https://docs.pytest.org/en/7.3.x/how-to/nose.html
Fixes: 482ef90aeb ("test: efi_capsule: refactor efi_capsule test")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The devnum value of the blk_desc structure starts from 0,
current efi_bl_create_block_device() function creates
two "efiblk#0" devices for the cases that blk_find_max_devnum()
returns -ENODEV and blk_find_max_devnum() returns 0(one device
found in this case).
This commit uses blk_next_free_devnum() instead of blk_find_max_devnum().
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
A previous patch is removing the last consumer of efi_remove_protocol().
Switch that to static and treat it as an internal API in order to force
users install and remove protocols with the appropriate EFI functions.
It's worth noting that we still have files using efi_add_protocol(). We
should convert all these to efi_install_multiple_protocol_interfaces()
and treat efi_add_protocol() in a similar manner
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The TCG2 protocol currently adds and removes protocols with
efi_(add/remove)_protocol().
Removing protocols with efi_remove_protocol() might prove
problematic since it doesn't call DisconnectController() when
uninstalling the protocol and does not comply with the UEFI specification.
It's also beneficial for readability to have protocol installations and
removals in pairs -- IOW when efi_install_multiple_protocol_interfaces()
is called, efi_uninstall_multiple_protocol_interfaces() should be used to
remove it. So let's swap the efi_add_protocol() as well.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
- Merge in some Kconfig dependencies fixes, typo fixes, erofs update,
shell portability fix, an env save fix, better mbr+gpt support, and
some android A/B enhancements.
