CFG_MXC_USB_FLAGS is only used for drivers/usb/host/ehci-mx5.c, so it
can be removed from all the imx6/imx7/imx8m board config files.
mx51evk.h is the only place CFG_MXC_USB_FLAGS is not set to 0.
Suggested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Set the CONFIG_SPL_LOAD_FIT_ADDRESS for both verdin-imx8mm and
verdin-imx8mp configurations to specify the load address for FIT images
loaded by the SPL.
As per lastest instructions from NXP, the generation of a HABv4 CSF
(Command Sequence File) requires the U-Boot FIT image (u-boot.itb) load
address to be set to a fixed value when binman is used. The address is
defined by CONFIG_SPL_LOAD_FIT_ADDRESS.
Here we set CONFIG_SPL_LOAD_FIT_ADDRESS to an address 64MB past the
start of the DDR memory leaving plenty of room for the various DDR-
residing artifacts to be moved to their usual load addresses which are
close to the start of the DDR.
Signed-off-by: Rogerio Guerra Borin <rogerio.borin@toradex.com>
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Instead of using the local imx6sl-evk, imx6sl-pinfunc.h and
imx6sl.dtsi devicetree copies from U-Boot, convert the imx6sl-evk board
to OF_UPSTREAM so that the upstream kernel devicetree can be used instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Remove mx6slevk_spinor_defconfig and mx6slevk_spl_defconfig in
favor of having a single mx6slevk_defconfig to help reducing
the maintenance effort.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The SD card is registered as mmc device 0.
Fix it accordingly so that the board can boot to Linux
from the SD card.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Depending on if a SPI-NOR flash is populated add the mtd partition
table to the device tree. For this we have to also probe the
flash before booting.
Signed-off-by: Benjamin Hahn <B.Hahn@phytec.de>
Add a new ahab_derive command that derives the hardware unique key (HUK)
into a 16 or 32 bytes key and stores it at the given address.
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Ye Li <ye.li@nxp.com>
The commit b81e31a1e6 ("bootstash: Do not provide a default address
for all") changed a bootstage unstash call to bootstage stash, this
has resulted in bootstage records stashed in SPL no longer get unstaged
in U-Boot proper. Fix this by changing back to a unstage call.
Fixes: b81e31a1e6 ("bootstash: Do not provide a default address for all")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Fix signed vs unsigned compare in read check in _spl_load()
Issue: when info->read() returns a negative value because of an error,
the comparison of 'read' (signed) with 'sizeof(*header)'
(unsigned silently converts the negative value into a very
large unsigned value and the check on the error condition
always return false, i.e. the error is not detected
Symptoms: if spl_load_image_fat() is unable to find the file 'uImage',
the SPL phase of the boot process just hangs after displaying
the following line:
Trying to boot from MMC1
Fix: cast 'sizeof(*header)' to int so the compare is now between
signed types
Reference: https://stackoverflow.com/questions/17293749/sizeof-operator-in-if-statement
Signed-off-by: Franco Venturi <fventuri@comcast.net>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
In the 7th generation of the SoC from Aspeed, the control logic of the
GPIO controller has been updated to support per-pin control. Each pin now
has its own 32-bit register, allowing for individual control of the pin’s
value, direction, interrupt type, and other settings.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
The Linux kernel documentation has transitioned from using
kconfig-language.txt to kconfig-language.rst. Therefore update all
occurrences of kconfig-language.txt.
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Enabling CONFIG_DM_SEQ_ALIAS enables code which relies on
`trailing_strtol()` - which is only linked in SPL when CONFIG_SPL_STRTO
is enabled.
CONFIG_SPL_STRTO is not enabled by default - to ensure this function is
available in SPL, CONFIG_SPL_DM_SEQ_ALIAS should select
CONFIG_SPL_STRTO.
Signed-off-by: Oliver Gaskell <Oliver.Gaskell@analog.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Shifting this pointer in the loop will be more logical when working
with the code later, because you can see at a glance what exactly
changes at each iteration. Moreover, the code remains equivalent
because this variable is not used after the loop.
Signed-off-by: Maxim Moskalets <maximmosk4@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Jonas Karlman <jonas@kwiboo.se> says:
Use of fdt_parent_offset() is very expensive as detailed by the function
documentation:
NOTE: This function is expensive, as it must scan the device tree
structure from the start to nodeoffset, *twice*.
This series remove multiple calls to fdt_parent_offset() or
ofnode_get_parent() when instead a single call can be made and the
returned value can be reused.
This series help reduce boot time by around:
- ~137ms on a Radxa ROCK Pi 4 (RK3399)
- ~33ms on a Radxa ZERO 3W (RK3566)
The counter value read from TDR register may not be correct.
Read SECCNT and CNTR25M instead to get the correct timestamp.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Until a live tree is used in U-Boot proper after relocation, use of
ofnode_get_parent() will trigger a call to the very expensive
fdt_parent_offset(), as detailed by the function documentation:
NOTE: This function is expensive, as it must scan the device tree
structure from the start to nodeoffset, *twice*.
Re-use the returned value from a single call instead of having to make
multiple calls for same node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Until a live tree is used in U-Boot proper after relocation, use of
ofnode_get_parent() will trigger a call to the very expensive
fdt_parent_offset() as detailed by the function documentation:
NOTE: This function is expensive, as it must scan the device tree
structure from the start to nodeoffset, *twice*.
Re-use the returned value from a single call instead of having to make
multiple calls for same node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use of fdt_parent_offset() is very expensive as detailed by the function
documentation:
NOTE: This function is expensive, as it must scan the device tree
structure from the start to nodeoffset, *twice*.
Re-use the returned value from a single call instead of having to make
multiple calls for same nodeoffset.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Nuvoton BMC NPCM7xx/NPCM8xx sgpio driver.
BMC can use this driver to increase 64 GPI pins and 64 GPO pins to use.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Add test cases for sf commands to verify various SPI flash operations
such as erase, write and read. It also adds qspi lock unlock cases.
This test relies on boardenv_* configurations to run it for different
SPI flash family such as single SPI, QSPI, and OSPI.
Signed-off-by: Love Kumar <love.kumar@amd.com>
Currently uclass index is used for bind/unbind which ignores alias
sequence numbering. Use device sequence number instead as it's
the number explicitly set in the DT.
Also update documentation to use sequence number.
Signed-off-by: Zixun LI <admin@hifiphile.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently uclass index is shown in DM tree dump which ignores alias
sequence numbering. The result could be confusing since these 2 numbers
could be different. Show device sequence number instead as it's more
meaningful.
Also update documentation to use sequence number.
Signed-off-by: Zixun LI <admin@hifiphile.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If the function is called with no NAND device attached, then this
function can return error value, proceeding further ignoring the same
can cause system crash. This is seen when "mtd list" is run with no NAND
addon cards connected.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
The sandbox pinmux driver is used in the non-test devicetree as well as
the test one. I didn't realize this when I modified the driver for
tests, and so broke the regular use case (which only resulted in
warnings). First, making the pinmux and the UART group available
pre-relocation to avoid ENODEV errors. Then, convert the pin groups and
functions to the new style, adding onewire group as well.
Fixes: 7f0f1806e3 ("test: pinmux: Add test for pin muxing")
Closes: https://source.denx.de/u-boot/u-boot/-/issues/2
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A system may have multiple SATA controller. Removing the controller with
the lowest sequence number before probing all SATA controllers makes no
sense.
In sata_rescan we remove all block devices which are children of SATA
controllers. We also have to remove the bootdev devices as they will be
created when scanning for block devices.
After probing all SATA controllers we must scan for block devices otherwise
we end up without any SATA block device.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for upstream linux split PCIe node.
Upstream linux have an alternative way to declare PCIe nodes that splits
them in dedicated nodes for each line instead of putting them all in one
node.
Detect this by checking if the mediatek,generic-pciecfg node is passed
as it's used to reference the common address for all the PCIe lines.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
uc_pdata->name is populated from device tree property "remoteproc-name".
For those devcices that don't set "remoteproc-name", uc_pdata->name
falls back to dev->name.
If two devices have same name, this will result into uc_pdata->name not
being unique and rproc_init() will fail.
Fix this by using combination of dev->name and dev->parent->name instead
of using just the dev->name to populate uc_pdata->name.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Andrew Davis <afd@ti.com>
Jonathan Humphreys <j-humphreys@ti.com> says:
Upstream DTS added explicit ranges to the fss node. It did not include
the 32 bit memory space needed by the R5 to access OSPI. With the
upstream DTS sync, OSPI boot no longer works.
Adding the missing range here. It is also being added in the upstream DTS,
so after the next upstream DTS sync, these patches can be removed.
Fixes: 5024a96db8 ("Subtree merge tag 'v6.10-dts' of devicetree-rebasing repo [1] into dts/upstream")
When a device fails to probe, the next device should be tried, until
either we find a suitable device or run out of devices. A device
should never be tried twice.
When we run out of devices of a particular priority, the hunter should
be used to generate devices of the next priority. Only if all attempts
fail should this function return an error.
Update the function to use the latent 'found' boolean to determine
whether another loop iteration is warranted, rather than setting 'dev'
to NULL, which creates confusion, suggesting that no devices have been
scanned and the whole process is starting from the beginning.
Note that the upcoming bootflow_efi() test is used to test this
behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: https://source.denx.de/u-boot/custodians/u-boot-dm/-/issues/17
This turns out to be insufficient to fix the problem, since when
bootdev_next_prio() exits, the caller has no idea that this really
is the end. Nor is it, since there may be other devices which should
be checked.
The caller iterates which calls iter_incr() which calls
bootdev_next_prio() again, which finds the same device and the loop
continues.
We never did create a test for this[1], which makes it hard to be
sure which problem was fixed.
The original code had the virtue of staying in the loop looking for a
bootdev, so let's go back to that and try to fix this another way.
A future patch will make bootdev_next_prio() continue after failure
which should provide same effect.
This reverts commit 9d92c418ac.
Signed-off-by: Simon Glass <sjg@chromium.org>
Upstream DTS added explicit ranges to the fss node. It did not include the
32 bit memory space needed by the R5 to access OSPI. With the upstream DTS
sync, OSPI boot no longer works.
Adding the missing range here. It is also being added in the upstream DTS,
so after the next upstream DTS sync, this patch can be removed. See
0c0e03ec22 (arm64: dts: ti: k3-j721e: Use exact ranges for FSS node)
Fixes: 5024a96db8 ("Subtree merge tag 'v6.10-dts' of devicetree-rebasing repo [1] into dts/upstream")
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Upstream DTS added explicit ranges to the fss node. It did not include the
32 bit memory space needed by the R5 to access OSPI. With the upstream DTS
sync, OSPI boot no longer works.
Adding the missing range here. It is also being added in the upstream DTS,
so after the next upstream DTS sync, this patch can be removed. See
0c0e03ec22 (arm64: dts: ti: k3-j721e: Use exact ranges for FSS node)
Fixes: 5024a96db8 ("Subtree merge tag 'v6.10-dts' of devicetree-rebasing repo [1] into dts/upstream")
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Upstream DTS added explicit ranges to the fss node. It did not include the
32 bit memory space needed by the R5 to access OSPI. With the upstream DTS
sync, OSPI boot no longer works.
Adding the missing range here. It is also being added in the upstream DTS,
so after the next upstream DTS sync, this patch can be removed. See
f00e626085 (arm64: dts: ti: k3-j7200: Use exact ranges for FSS node)
Fixes: 5024a96db8 ("Subtree merge tag 'v6.10-dts' of devicetree-rebasing repo [1] into dts/upstream")
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
Upstream DTS added explicit ranges to the fss node. It did not include the
32 bit memory space needed by the R5 to access OSPI. With the upstream DTS
sync, OSPI boot no longer works.
Adding the missing range here. It is also being added in the upstream DTS,
so after the next upstream DTS sync, this patch can be removed. See
f062a015f4 (arm64: dts: ti: k3-j784s4: Use exact ranges for FSS node)
Fixes: 5024a96db8 ("Subtree merge tag 'v6.10-dts' of devicetree-rebasing repo [1] into dts/upstream")
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Upstream DTS added explicit ranges to the fss node. It did not include the
32 bit memory space needed by the R5 to access OSPI. With the upstream DTS
sync, OSPI boot no longer works.
Adding the missing range here. It is also being added in the upstream DTS,
so after the next upstream DTS sync, this patch can be removed. See
f062a015f4 (arm64: dts: ti: k3-j784s4: Use exact ranges for FSS node)
Fixes: 5024a96db8 ("Subtree merge tag 'v6.10-dts' of devicetree-rebasing repo [1] into dts/upstream")
Signed-off-by: Jonathan Humphreys <j-humphreys@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Simon Glass <sjg@chromium.org> says:
This series started as a small fix for checking for an empty line,
but in the process several other problems were found and fixed:
- fix tests which use console recording but don't set the flag
- drop unnecessary resetting of the console in tests
- drop unnecessary blank line before MMC output
- update the docs a little
- fix buildman test failure on newer Pythons
- a few other minor things
This series also renames the confusing flag names, so that they are
easier to remember - just a UTF_ (unit-test flags) prefix.
Set this flag rather than doing things manually in the test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
It is seldom necessary to call this function. Drop its use in the
command tests.
Add a few extra checks to the wget test so that resetting is not
needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fabio EstevamandFabio Estevam
Rogerio Guerra BorinandFabio Estevam
Tomas PaukrtandFabio Estevam
Benjamin HahnandFabio Estevam
Mathieu OthaceheandFabio Estevam
Jonas KarlmanandTom Rini
Franco VenturiandTom Rini
Billy TsaiandTom Rini
Hiago De FrancoandTom Rini
Gaskell, OliverandTom Rini
Jim LiuandTom Rini
Maxim MoskaletsandTom Rini
Love KumarandTom Rini
Zixun LIandTom Rini
Vignesh RaghavendraandTom Rini
Derald D. WoodsandTom Rini
Sean AndersonandTom Rini
Heinrich SchuchardtandTom Rini
Christian MarangiandTom Rini
MD Danish AnwarandTom Rini
Simon GlassandTom Rini
Jonathan HumphreysandTom Rini