Add 10GBE high-speed Mac support, it supports 10G, 5G, 2.5G and 1G speeds.
10GBE high speed Mac is an extension of the current 1G Mac in versal,
inheriting all its current features.
MMI 10GBE ip has two internal PCS's.
1)10GBASER PCS is used for higher speeds 10G and 5G.
2)1000BASEX PCS is used for slower speeds 1G and 2.5G.
Both PCS's speed and rate configuration is done with same
usx registers. ENABLE_HS_MAC bit in NCR is the toggle switch
between the PCS's.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250828045807.426542-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Configure RMMI and M-PHY registers for HS mode required for selection of
bit rate series A or B. If it is not a calibrated part, then switch back
to SLOWAUTO_MODE and skip all these configurations.
Implemented below sequence as per the DWC RMMI databook.
1. Override RMMI CBRATESEL with the desired rate.
2. Set TX_CFGUPDT_0 to 1'b1 for one TX_CFGCLK_0 cycle.
3. Override PHY rx_req to 1, then poll on PHY rx_ack register till it
goes 1(both lanes).
4. Override PHY rx_req to 0, then poll on PHY rx_ack register till it
goes 0(both lanes).
5. Remove PHY rx_req override(both lanes).
6. Start the LS PMC.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250724044402.260149-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The kernel-doc comment for the axi_mrmac_recv function was missing
the colon (':') after the '@packetp' parameter tag.
The kernel-doc comment for the axi_mrmac_free_pkt function was missing
the colon (':') after the 'length' parameter tag.
This caused a Sparse warnings regarding the 'packetp' and 'length'
parameters not being described. Fix the formatting to align
with kernel-doc standards and resolve the warning.
drivers/net/xilinx_axi_mrmac.c:357:
warning: Function parameter or member 'packetp' not described
in 'axi_mrmac_recv'
drivers/net/xilinx_axi_mrmac.c:411:
warning: Function parameter or member 'length' not described
in 'axi_mrmac_free_pkt'
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250717044855.1359443-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The 'dev' parameter in the zynq_gpio_get_bank_pin function was not
described in its kernel-doc comment block, leading to a Sparse warning.
drivers/gpio/zynq_gpio.c:194: warning: Function parameter or member 'dev'
not described in 'zynq_gpio_get_bank_pin'
Add a description for the 'dev' parameter to satisfy the documentation
requirements and improve code clarity for this function.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250717044632.1353588-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
In DDR mode, even bytes are read using DMA, while the remaining odd
bytes are read using STIG mode. However, the data is not correctly
transferred into the flash read data lower register because the
supplementary byte of the STIG opcode is not being written to the
opcode extension register, resulting in incorrect data being read.
To resolve this issue, when using STIG transactions, the corresponding
supplementary byte of any STIG opcode must be defined in the Opcode
Extension Register (Lower). Issue has been observed on the Macronix
MX66UM2G45G flashes.
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250702053953.640046-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
tshsl_ns is the clock delay for chip select deassert. This is the delay in
master reference clocks for the length that the master mode chip select
outputs are de-asserted between transactions.
The minimum delay is always SCLK period to ensure the chip select is never
re-asserted within one SCLK period.
That is why tshsl_ns delay should be at least one sclk_ns value. If it is
less than sclk_ns, set it equal to sclk_ns.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250702065717.3871435-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Starting from 'commit <8077d296adff> ("spi: cadence-quadspi: Use STIG
mode for all ops with small payload") the utilization of STIG mode
has been implemented for read and write operations involving less
than 8 bytes of data.
However, following this commit, encountering timeout issues occurs when
writing odd bytes of data in DDR mode, as indicated below:
"jedec_spi_nor flash@0: flash operation timed out
SF: 3 bytes @ 0x0 Written: ERROR -110"
To resolve this issue, the number of bytes to write has been updated
specifically for DDR mode.
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250704040444.671604-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Legacy SPI flash devices used a 24-bit (3-byte) addressing scheme,
limiting the addressable memory to 16 MB. To support larger densities
(256 Mbit and higher), extended addressing schemes, such as 32-bit
(4-byte) addressing, were introduced. If the flash density exceeds
16 MB and CONFIG_SPI_FLASH_BAR is disabled, the device will use a
4-byte addressing mode.
Signed-off-by: Prasad Kummari <prasad.kummari@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250707043738.795179-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Observing the crash when we add the i2c-arbitrator node in the device
tree as per the DT bindings. The issue is with the child node of
i2c-arbitrator@72 i.e., i2c@f1950000->i2c-arbitrator@72->i2c-arb, as the
arbitrator uses the uclass of mux(UCLASS_I2C_MUX) and the mux uclass driver
checks for the "reg" property using the i2c_mux_child_post_bind() function,
if it won't find the "reg" property it will return -EINVAL which is leading
to the crash.
So, add the logic to check whether the child node has the "reg" property,
if the "reg" property exists then read the "reg" and update the channel.
https://www.kernel.org/doc/Documentation/devicetree/bindings/i2c/i2c-arb.txt
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Write enable(06h) command will be sent to a flash device to
set the write enable latch bit before every program, erase,
write command. After that write disable command (04h) needs
to be sent to clear the write enable latch.
This write_disable() is missing at the majority of the places
in the driver, add it to clear write enable latch.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://gist.github.com/PrasanthBabuMantena/c12f39744de188a9d08cd5ca51dc2a7b
Tested-by: Prasanth Babu Mantena <p-mantena@ti.com>
Since the opcode SPINOR_OP_CHIP_ERASE (0xc7) is not supported
for the mt35xu01g/2g flashes, the NO_CHIP_ERASE flag has been added
to enable sector erase functionality instead.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
HBM stands for high bandwidth memory and is a type of memory interface used
in 3D-stacked DRAM (dynamic random access memory) in some AMD GPUs (aka
graphics cards), as well as the server, high-performance computing (HPC)
and networking and client space. High Bandwidth Memory(HBM) has total 16
channels, one channel is divided into two pseudo channels which makes its
32 banks each with some amount of memory.
And then we have DDR_LOW PS low, DDR_HIGH0 PS high, DDR_HIGH1 PS very high
and pretty much there should be also place for PL DDR. So maximum number of
memory banks will be 36, updating the CONFIG_NR_DRAM_BANKS to 36.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20250410092528.3713904-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add the basic 'hello world ta' command which increment
of the value passed. This provides easy test for
establishing a session with OP-TEE TA and verify.
It includes following "hello world ta" subcommands:
optee hello; default value '0' is passed and gets incremented.
optee hello <value>; value to increment via OP-TEE HELLO
WORLD TA.
To enable the OP-TEE side HELLO WORLD example please refer
https://optee.readthedocs.io/en/latest/building/gits/optee_examples/optee_examples.html
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Jerome Forissier <jerome.forissier@linaro.org>
Update the spi_nor_read() function based on the config SPI_FLASH_BAR
and update the length and bank calculation by spliting the memory of
16MB size banks only when the address width is 3byte.
Fix the read issue for 4byte address width by passing the entire
length to the read function.
Fixes: 5d40b3d384 ("mtd: spi-nor: Add parallel and stacked memories support")
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
As the flash reset is handled in spi nor core, removing the
flash reset functionality. As the configuration like tristate
and hysterisis need to be enabled by the cdo. Handle the flash
reset only for mini u-boot case.
Rename the "cadence_qspi_versal_flash_reset" to generic name
"cadence_qspi_flash_reset" as this can be used by other platforms
as well.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20241108063537.13180-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The .bind function is implemented to bind the correct
"half" of the hub that the driver wants to bind,
and returning -ENODEV for the other "half".
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add i2c initialization hook and set usb5744 platform
data with function having required i2c initialization sequence.
Apart from the USB command attach, prevent the hub from suspend.
when the “USB Attach with SMBUS (0xAA56)” command is issued to the hub,
the hub is getting enumerated and then it puts in a suspend mode.
This causes the hub to NAK any SMBUS access made by the SMBUS Master
during this period and not able to see the hub's slave address while
running the "i2c probe" command.
Prevent the MCU from the putting the HUB in suspend mode through register
write. The BYPASS_UDC_SUSPEND bit (Bit 3) of the RuntimeFlags2 register at
address 0x411D controls this aspect of the hub. The BYPASS_UDC_SUSPEND
bit in register 0x411Dh must be set to ensure that the MCU is always
enabled and ready to respond to SMBus runtime commands. This register
needs to be written before the USB attach command is issued.
The byte sequence is as follows:
Slave addr: 0x2d 00 00 05 00 01 41 1D 08
Slave addr: 0x2d 99 37 00
Slave addr: 0x2d AA 56 00
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add support for the Microchip USB5744 USB3.0 and USB2.0 Hub.
The usb5744 driver trigger hub reset signal after soft reset.
The usb5744 hub need to reset after the phy initialization,
which toggles the gpio.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Don't error out if there is no vdd regulator supply, as these are
optional properties.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Marek Vasut <marex@denx.de>
As part of the reset, sets the direction of the pin to output before
toggling the pin. Delay of millisecond is added in between low and
high to meet the setup and hold time requirement of the reset.
Update the usb2514 hub_data with the reset delay and power on
delay values.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Moving the hw_reset function from the controller driver to
the NOR framework has caused the OSPI reset not to be triggered
in the Cadence driver's probe function. As a result, reading the
flash ID during SPI calibration is incorrect, and the
CQSPI_REG_RD_DATA_CAPTURE is set with an invalid value.This makes
it unable to read the flash ID properly.
To solve this problem, it's suggested to skip SPI calibration and
instead retrieve the read_delay directly from the device tree.
Skipping SPI calibration doesn't bring harm since there's no need
for the flash golden values stored during SPI calibration.
Instead, they are now read during the spi_nor_read_id call in the
NOR framework.
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20241114062045.17581-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Enable the SPI_ADVANCE config option for all xilinx platforms, as
this is required for parallel-memories.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Add support for parallel memories in zynq_qspi.c driver. In case of
parallel memories STRIPE bit is set and sent to the qspi ip, which will
send data bits to both the flashes in parallel. However for few commands
we should not use stripe, instead send same data to both the flashes.
Those commands are exclueded by using zynqmp_qspi_update_stripe().
Also update copyright info for this file.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Add support for parallel memories in zynqmp_gqspi.c driver. In case of
parallel memories STRIPE bit is set and sent to the qspi ip, which will
send data bits to both the flashes in parallel. However for few commands
we should not use stripe, instead send same data to both the flashes.
Those commands are exclueded by using zynqmp_qspi_update_stripe().
Also update copyright info for this file.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Read chipselect properties from DT which are populated using 'reg'
property and save it in plat->cs[] array for later use.
Also read multi chipselect capability which is used for
parallel-memories and return errors if they are passed on using DT but
driver is not capable of handling it.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
In parallel mode, the current implementation assumes that a maximum of
two flashes are connected. The QSPI controller splits the data evenly
between both the flashes so, both the flashes that are connected in
parallel mode should be identical.
During each operation SPI-NOR sets 0th bit for CS0 & 1st bit for CS1 in
nor->flags.
In stacked mode the current implementation assumes that a maximum of two
flashes are connected and both the flashes are of same make but can
differ in sizes. So, except the sizes all other flash parameters of both
the flashes are identical
Spi-nor will pass on the appropriate flash select flag to low level
driver, and it will select pass all the data to that particular flash.
Write operation in parallel mode are performed in page size * 2 chunks as
each write operation results in writing both the flashes. For doubling
the address space each operation is performed at addr/2 flash offset,
where addr is the address specified by the user.
Similarly for read and erase operations it will read from both flashes,
so size and offset are divided by 2 and send to flash.
Adding the config option SPI_ADVANCE for non SPL code.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
By default flash lock option is enabled, enable this option only
when it is required. By disabling the lock config will save some
amount of memory.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
This patch fixes timeout issues seen on large NOR flash.
For full-chip erase, where we use the SPINOR_OP_CHIP_ERASE (0xc7)
opcode. Use a different timeout for full-chip erase than for other
commands.
[Ported from Linux kernel commit
09b6a377687b ("mtd: spi-nor: scale up timeout for
full-chip erase") ]
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Per JESD84-B51 P47, host need to change frequency to <=52MHz
after setting HS_TIMING to 0x1, and host need to set the
8-bit DDR buswidth. Currently setting the frequency to 26MHz
and trying to switch 8-bit DDR buswidth resulting timeouts.
mmc dev 1 0
Select HS400 failed -110
switch to partitions #0, OK
mmc1(part 0) is current device
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
This enables boards to choose where to/from the environment
should be saved/loaded. They can then for example support using
the same device (dynamically) from which the bootloader was
launched to load and save env data and do not have to
define CONFIG_ENV_SPI_BUS statically.
In my use case, the environment needs to be on the same device I
booted from. It can be the QSPI or OSPI device.
I therefore would override spi_get_env_dev in the board code,
read the bootmode registers to determine where we booted from
and return the corresponding device index.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20240614124811.22945-2-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com> # Move spi_get_env_dev to sf.c
Enable setting speed mode using mmc dev commands.
The speed mode is provided as the last argument in these commands
(ex: mmc dev 0 0 10) and is indicated using the index from enum
bus_mode in include/mmc.h. A speed mode can be set if it is enabled
from device tree or from capabilities register
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20240708091755.5021-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
SOC can boot out of the device which is not accessible from APU and running
this is detected as a warning, as the device is not accessible.For example
getting below warning when the boot mode is OSPI and OSPI is not enabled in
device tree.
Invalid bus 0 (err=-19)
Failed to initialize SPI flash at 0:0 (error -19)
Ignoring the prioritization of the boot device which driver is not enabled
and continue with the default boot_targets. Recommendation is to use custom
boot_targets via environment file as is done for example for Kria via
zynqmp_kria.env file.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/8b7cca5c7b84cb4854104e0c48f8aa63c4ec5ace.1715322156.git.michal.simek@amd.com
Arm's GIC-600 features a Power Register (GICR_PWRR),
which needs to be programmed to enable redistributor
operation. Power on the redistributor and wait until
the power on state is reflected by checking the bit
GICR_PWRR.RDPD == 0. While running U-Boot in EL3
without enabling this register, GICR_WAKER.ChildrenAsleep
bit is not getting cleared and loops infinitely.
This register(GICR_PWRR) must be programmed to mark the frame
as powered on, before accessing other registers in the frame.
Rest of initialization sequence remains the same.
ARM GIC-600 IP complies with ARM GICv3 architecture.
Enable this config if GIC-600 IP present.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Currently when using "W=1" with xilinx_zynqmp_r5_defconfig, getting
below warnings.
cc1.real: warning: ./arch/arm/mach-zynqmp-r5/include:
No such file or directory [-Wmissing-include-dirs]
Fix W=1 missing-include-dirs warnings by including the headers and
sys_r5_proto.h file which can be used.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20240111030029.2565827-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
