Instead of using defines for the RAM size and base address, retrieve these
information from the devicetree.
This aligns with the sama5d27_som1_ek board in commit 73c1589f02
("board: sama5d27_som1_ek: Get dram size and base from device tree").
While at it, remove a spurious '/* SPL */' comment.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Since commit b4734c9c33 ("clk: imx: Convert clock-osc-* back to osc_*")
SPL takes a long time to load U-Boot proper on an imx8mm-evk board.
The reason for the long delay is because the osc_32k clock is not available
in the SPL phase.
Fix this problem by passing the 'bootph-all' and 'bootph-pre-ram'
properties to make the osc_32k clock available in SPL.
This also aligns with imx8mn and imx8mp-u-boot.dtsi files.
Fixes: b4734c9c33 ("clk: imx: Convert clock-osc-* back to osc_*")
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Adam Ford <aford173@gmail.com>
The PIT timer needs to be available early in the SPL phase,
otherwise SPL fails to boot and only prints:
Could not initialize timer (err -96)
Fix this problem by passing 'bootph-all' to the sama5d2 PIT node.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Since commit 61040097a9 ("reset: at91: Add reset driver for basic
assert/deassert operations") the "atmel,sama5d3-rstc" compatible for
the sama5d2 reset controller in sama5d2.dtsi is not handled by
CONFIG_SYSRESET_AT91 anymore, but by CONFIG_RESET_AT91 now.
This resulted in the following error, when trying to reset from the U-Boot
shell on a sama5d27_wlsom1 board:
=> reset
resetting ...
System reset not supported on this platform
### ERROR ### Please RESET the board ###
Fix it by enabling the CONFIG_RESET_AT91 driver in all sama5d27 defconfigs.
Tested on a sama5d27_wlsom1 board.
Based on the fix in commit e1ee52ca56 ("configs: at91: sam9x60: Switch
to new reset driver")
Fixes: 61040097a9 ("reset: at91: Add reset driver for basic assert/deassert operations")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Guard the inclusion of tee.bin with the CONFIG_OPTEE symbol to fix the
following build warning:
CHECK u-boot-container.cfgout
WARNING './tee.bin' not found, resulting binary may be not-functional
BINMAN .binman_stamp
OFCHK .config
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The imx6q-lxr devicetree has landed in kernel 6.13.
Switch to OF_UPSTREAM to make use of the upstream devicetree.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Currently, booting via bootstd fails because the kernel cannot be retrieved.
The reason for this is the lack of 'kernel_addr_r'.
Pass 'kernel_addr_r' to fix booting via bootstd.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Currently, booting via bootstd fails because the kernel cannot be retrieved.
The reason for this is the lack of 'kernel_addr_r'.
Pass 'kernel_addr_r' to fix booting via bootstd.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Guard binman nodes with CONFIG_OPTEE to fix the following error
when building without optee support:
BINMAN .binman_stamp
Image 'image' has faked external blobs and is non-functional: tee.bin
Image 'image' is missing optional external blobs but is still functional: tee-os
/binman/section/fit/images/tee/tee-os (tee.bin):
See the documentation for your board. You may need to build Open Portable
Trusted Execution Environment (OP-TEE) and build with TEE=/path/to/tee.bin
Some images are invalid
make: *** [Makefile:1135: .binman_stamp] Error 103
While at it, only pass tee to the loadables lines when CONFIG_OPTEE is
defined.
Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Yannic Moog <y.moog@phytec.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
With CONFIG_DM_USB, there is no longer the need for any USB board code
anymore.
Remove the unneeded USB board code.
While at it, also remove the uneeeded CONFIG_USB_MAX_CONTROLLER_COUNT
option.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The LXR2 board has a DA9063 that can provide watchdog functionality.
The DA9063 watchdog can cause a full POR reset, which is preferred
over the built-in i.MX6 watchdog.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The DA9063 PMIC is a multi-function device that provides
regulator, watchdog, RTC, and ON key functionalities.
Add support for the DA9063 PMIC watchdog functionality.
Based on the 6.11 kernel drivers/watchdog/da9063_wdt.c driver.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for the Comvetia i.MX6Q LXR2 board, which is
uses the Phytec PFLA02 SoM.
Based on the original work from Stefano Babic <sbabic@denx.de>.
The Phytec PFLA02 devicetrees are taken from kernel 6.11-rc7.
The imx6q-lxr.dts has been submitted upstream:
https://lore.kernel.org/linux-devicetree/20240913200906.1753458-3-festevam@gmail.com/
After it gets accepted in mainline (most likely in kernel 6.13),
the lxr2 board can then be switched to OF_UPSTREAM and these device trees
can be removed from U-Boot.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The definition of CFG_MXC_USB_PORTSC as (PORT_PTS_UTMI | PORT_PTS_PTW)
can be removed from mx5/mx6/mx7/mx8m board config files as it is the
default in drivers/usb/host/ehci-mx5.c and drivers/usb/host/ehci-mx6.c.
Suggested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Just like drivers/usb/host/ehci-mx6.c, add a default for
drivers/usb/host/ehci-mx5.c.
The motivation for doing this is to remove CFG_MXC_USB_PORTSC
from board config files.
All the mx5 boards, with the exeption of mx51evk, define
CFG_MXC_USB_PORTSC as:
#define CFG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
So move this definition as a default into ehci-mx5.c.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
CFG_MXC_USB_FLAGS is only used for drivers/usb/host/ehci-mx5.c, so it
can be removed from all the imx6/imx7/imx8m board config files.
mx51evk.h is the only place CFG_MXC_USB_FLAGS is not set to 0.
Suggested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Instead of using the local imx6sl-evk, imx6sl-pinfunc.h and
imx6sl.dtsi devicetree copies from U-Boot, convert the imx6sl-evk board
to OF_UPSTREAM so that the upstream kernel devicetree can be used instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Remove mx6slevk_spinor_defconfig and mx6slevk_spl_defconfig in
favor of having a single mx6slevk_defconfig to help reducing
the maintenance effort.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The SD card is registered as mmc device 0.
Fix it accordingly so that the board can boot to Linux
from the SD card.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Currently, the bmode command only supports booting from ecspi1.
Expand it to also support booting from ecspi3.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Remove several comments that do not apply anymore to
the current file content.
While at it, write 'PMIC' into a single line for consistency.
Signed-off-by: Fabio Estevam <festevam@denx.de>
With DM_SERIAL in place, there is no need to setup the UART pins
in the board code.
The UART pins are setup via devicetree, thanks to DM.
Remove the unneeded code.
Signed-off-by: Fabio Estevam <festevam@denx.de>
CONFIG_DM_MMC and CONFIG_DM_SPI are alway selected so the mmc
and spi board code can be safely removed.
Remove it to make the code cleaner.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Currently, the devicetree model as well as the board variant name
are shown:
...
Model: TQ TQMa6S/DL on MBa6x
Board: TQMa6DL on a MBa6x
...
Unselect the CONFIG_DISPLAY_BOARDINFO option so that the
board name is printed only once in board_late_init() instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Currently, the power_init_board() function is not executed because
CONFIG_POWER_LEGACY is not selected.
Convert to PMIC driver model, which allows removing board I2C code in
favor of the I2C driver model.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Instead of using the local imx6-tqma6 devicetree copies from U-Boot,
convert the imx6-tqma6 target to OF_UPSTREAM so that the upstream
kernel devicetrees can be used instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Booting an initramfs with the current initrd_addr address may lead to
initramfs corruption and boot failure.
Fix the initramfs problem by applying the following layout
suggested by Tom Rini:
loadaddr=0x40480000 --> Gets moved to 0x40600000 in run-time:
Uncompressing Kernel Image
Moving Image from 0x40480000 to 0x40600000, end=41e80000
fdt_addr_r= moved loadaddr + 128 MiB = 0x48600000
initrd_addr=fdt_addr_r + 512 KiB = 0x48680000
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Newer versions of the imx8mm-cl-iot-gate boards may come populated with a
Samsung 4GB DDR model.
Add support for it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The following information printed on every boot is not very
helpful for the users:
SOC: 0xa0009300
LC: 0x40040
Move them to debug() level.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Mathieu Othacehe <othacehe@gnu.org>
Add a weak default reset_cpu() implementation just like
it is done on arch/arm/mach-imx/cpu.c.
This allows the removal of the empty reset_cpu() in several
board files.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Hiago De Franco <hiago.franco@toradex.com> # Toradex Colibri iMX8X
There is no imx8mp-msc-sm2s.dtb file in upstream Linux.
Change it to imx8mp-msc-sm2s-ep1.dtb.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Ian Ray <ian.ray@gehealthcare.com>
Redundant environment support is required for software updates.
Add support for it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Ian Ray <ian.ray@gehealthcare.com>
Add mmc alias so that the eMMC is mmc0 and the SD card
is mmc1 to have a well defined device numbering scheme.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Ian Ray <ian.ray@gehealthcare.com>
Currently, the Ethernet ports are not working.
The Ethernet PHY reset lines are controlled by the TCA6424 I2C GPIO
expander.
The TCA6424 I2C GPIO expander is supported by the CONFIG_DM_PCA953X
driver.
Select the CONFIG_DM_PCA953X option so that the Ethernet PHYs can
go through a proper reset making Ethernet to be functional.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Ian Ray <ian.ray@gehealthcare.com>
With Ethernet DM in place, there is no longer the need for having
the board_phy_config() anymore.
Remove it.
Confirmed that TFTP transfer still works fine without board_phy_config().
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
U-Boot binary has grown in such a way that it goes beyond the reserved
area for the environment variables.
Running "saveenv" and rebooting the board causes U-Boot to hang because
of this overlap.
Fix this problem by selecting CONFIG_LTO so that the U-Boot proper
size can be reduced.
Also, to prevent this same problem to happen in the future, use
CONFIG_BOARD_SIZE_LIMIT, which can detect the overlap in build-time.
CONFIG_BOARD_SIZE_LIMIT is calculated as follows:
CONFIG_BOARD_SIZE_LIMIT = CONFIG_ENV_OFFSET - u-boot-img.dtb offset
CONFIG_BOARD_SIZE_LIMIT = 0xc000 - 69 * 1024
CONFIG_BOARD_SIZE_LIMIT = 715766
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
In an attempt to select ARMV8_SPL_EXCEPTION_VECTORS, the SPL size
could not fit into the internal SRAM of some imx8m targets:
aarch64: + imx8mm_phg
+aarch64-linux-ld.bfd: u-boot-spl section `__u_boot_list' will not fit in region `.sram'
+aarch64-linux-ld.bfd: region `.sram' overflowed by 1824 bytes
Select LTO to prevent that.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
All i.MX8M targets rely on using binman to generate the U-Boot
binary.
Select it at the SoC level instead of per board.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
All i.MX93 targets rely on using binman to generate the U-Boot
binary.
Select it at the SoC level instead of per board.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Adjust the underline length so that it matches the title length.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Selecting CONFIG_IMX_HAB=y on a SPL target, such as apalis_imx6_defconfig,
for example, leads to the following build error:
/usr/bin/arm-linux-gnueabihf-ld.bfd: arch/arm/mach-imx/hab.o: in function `imx_hab_is_enabled':
arch/arm/mach-imx/hab.c:879: undefined reference to `fuse_read'
fuse_read() comes from SPL_MXC_OCOTP, which depends on SPL_DRIVERS_MISC,
since commit 251a3053b1 ("misc: imx: remove DM dependency for ocotp
driver in SPL").
Select SPL_DRIVERS_MISC in the SPL case to fix this build issue.
Reported-by: Lisandro Pérez Meyer <lpmeyer@ics.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Lisandro Pérez Meyer <lpmeyer@ics.com>
With Ethernet DM in place, there is no longer the need for having
the board_phy_config() anymore.
Remove it.
Tested on imx7d-pico-pi board:
=> setenv autoload no
=> dhcp
BOOTP broadcast 1
*** Unhandled DHCP Option in OFFER/ACK: 42
DHCP client bound to address 192.168.0.138 (138 ms)
=> tftp zImage
Using ethernet@30be0000 device
TFTP from server 192.168.0.16; our IP address is 192.168.0.138
Filename 'zImage'.
Load address: 0x80800000
Loading: #################################################################
....
#################################################################
##########
4.3 MiB/s
done
Bytes transferred = 9034120 (89d988 hex)
Signed-off-by: Fabio Estevam <festevam@denx.de>
When CONFIG_DWC_ETH_QOS_IMX=y and CONFIG_FEC_MXC is not selected, the
following warning is seen:
arch/arm/mach-imx/imx8m/clock_imx8mm.c: In function 'board_interface_eth_init':
arch/arm/mach-imx/imx8m/clock_imx8mm.c:914:24: warning: implicit declaration of function 'imx8mp_fec_interface_init; did you mean 'imx8mp_eqos_interface_init'? [-Wimplicit-function-declaration]
Fix it by adding a stub for imx8mp_fec_interface_init() to handle this
case.
This follows the same approach done on imx8mp_eqos_interface_init().
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
With DM enabled, there is no need for board code to initialize
the Ethernet interfaces.
The RTL8211FDI Ethernet PHYs have 25MHz oscillator, so there is no
need to enable the RGMII TX clk output.
Also, there is no need for describing the deprecated phy-reset FEC
properties, nor passing reset properties to the EQOS interface in
u-boot.dtsi.
Remove all these unneeded pieces.
Tested both Ethernet interfaces after these changes.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Currently, when running "ums 0 mmc 2" and breaking it via
CTRL + C, the following message is seen:
u-boot=> ums 0 mmc 1
UMS: LUN 0, dev mmc 1, hwpart 0, sector 0x0, count 0x1dacc00
CTRL+C - Operation aborted
clk usb_phy_root_clk already disabled
The USB PHY clock is disabled twice: first it gets disabled
inside imx8mq_usb_phy_power_off(), then it is disabled again
inside imx8mq_usb_phy_exit().
Let the USB PHY clock be disabled only once inside
imx8mq_usb_phy_power_off() by removing the .exit operation.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Sync imx8mm.dtsi with linux-next 20231019.
The motivation for doing this sync was a bug when doing "ums 0 mmc 1"
on imx8mm-evk. It worked well for the first time, but after doing
a CTRL+C and launching the ums again, the command did not work.
Adam Ford suggested to sync imx8mm.dtsi with the Linux dts, as there was
a recent USB power domain reorganization there.
After syncing the imx8mm.dtsi with Linux, the ums command works without
problem after a CTRL+C.
Suggested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
I would like to help maintaining the imx8mp_evk board.
Add myself to MAINTAINERS.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Currently, the imx8mp_evk uses the non-DM code to initialize the PMIC.
Convert to DM_PMIC, which is the recommended way to access the PMIC.
While at it, fix multi-line comments style.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Commit 0aea5dda29 ("ARM: dts: imx7d-sdb-u-boot: Fix usdhc1 UHS
operation") did a temporary workaround by addng the usdhc1 fix
inside the -u-boot.dtsi file.
The imx7d-sdb.dts from kernel 6.5-rc1 contains the proper UHS
fix, so sync the devicetree tree and remove the previous fix
from -u-boot.dtsi.
Also, adjust the PMIC node name inside pmic_get() to match
the devicetree update.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Currently, building imx8qm_dmsse20a1_defconfig leads to the following
warning:
aarch64-linux-ld.bfd: invalid origin for memory region .sdram
Fix it by using the same SPL memory layout as done in the imx8mq_evk.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Oliver Graute <oliver.graute@kococonnector.com>
The aliases and chosen nodes are currently indented using spaces.
Fix them to use the standard tab indentation.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset
Signed-off-by: Fabio Estevam <festevam@denx.de>
On an early revision of the imx8mp-evk that I have access to,
the MAC addresses fuses are not programmed, causing failure to bring
the Ethernet interfaces.
Fix this problema by selecting CONFIG_NET_RANDOM_ETHADDR so that
random MAC addresses are assigned and the Ethernet ports become
functional out of the box.
Signed-off-by: Fabio Estevam <festevam@denx.de>
While bringinp up a new board without the MAC fuses programmed,
the following error message was observed:
Error: ethernet@30bf0000 address not set.
Improve the error message to make it clearer the reason of
the failure.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add USB0 OTG support.
Currently, the USB0 OTG nodes are not enabled in the Linux kernel
devicetree.
For this reason, enable the USB0 OTG nodes inside imx8mp-evk-u-boot.dtsi
for now.
Also select several useful options such as USB gadget and fastboot.
Tested by running "ums 0 mmc 2".
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Unselect CONFIG_CONSOLE_MUX to fix the following
error for the input, output and error interfaces:
U-Boot 2023.10 (Oct 03 2023 - 21:23:18 -0300)
...
In: No input devices available!
Out: No output devices available!
Err: No error devices available!
Net: eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
Signed-off-by: Fabio Estevam <festevam@denx.de>
The xfi3 target has been removed by commit 539fba2c10 ("arm:
Remove xfi3 board"), but it missed to remove an entry from the
mxs Kconfig.
Remove it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
SPDX-License tag is missing and checkpatch complains about it.
Add the SPDX-License tag using the same one from imx7d-sdb.dts.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Since commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable() may be EALREADY or
EBUSY for fixed/GPIO regulators.
Switch to using the more relaxed regulator_set_enable_if_allowed() to
continue if regulator already was enabled or disabled.
This fixes the following error when running the 'ums' command:
=> ums 0 mmc 0
UMS: LUN 0, dev mmc 0, hwpart 0, sector 0x0, count 0xece000
Error enabling VBUS supply
g_dnl_register: failed!, error: -114
g_dnl_register failed
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Use dev_ofnode() to retrieve the USB node pointer from the udevice
structure.
This fixes the following build error:
drivers/usb/host/ehci-mxs.c:143:38: error: 'struct udevice' has no member named 'node_'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Trying to boot a fitImage after a successful hab_auth_img operation
causes the following error:
## Loading kernel from FIT Image at 88000000 ...
Using 'conf-imx7d-smegw01.dtb' configuration
Trying 'kernel-1' kernel subimage
Description: Linux kernel
Type: Kernel Image
Compression: uncompressed
Data Start: 0x8800010c
Data Size: 9901752 Bytes = 9.4 MiB
Architecture: ARM
OS: Linux
Load Address: 0x80800000
Entry Point: 0x80800000
Hash algo: sha256
Hash value: 28f8779bbf010780f16dd3d84ecb9b604c44c5c2cf7acd098c264a2d3f68e969
Verifying Hash Integrity ... sha256Error in SEC deq
CAAM was not setup properly or it is faulty error!
The reason for this error is that the BootROM uses the CAAM Job Ring 0,
so disable its node in U-Boot to avoid the resource conflict.
imx8m dtsi files also have the Job Ring 0 disable since the following
kernel commit:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/arch?h=v6.5&id=dc9c1ceb555ff661e6fc1081434600771f29657c
For a temporary solution, disable the Job Ring 0 in imx7s-u-boot.dtsi.
Reported-by: Eduard Strehlau <eduard@lionizers.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
The ivt_offset parameter is optional for both hab_auth_img_or_fail
and hab_auth_img commands.
Document it in their usage texts to make it clearer.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Vanessa's NXP e-mail is no longer active.
Contacted her offline and she told me that she does not have
access to the board anymore and it is OK to remove her
from MAINTAINERS.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Polling every second to check whether the CPU has cooled down is
too frequent.
Allow more time for the CPU to cool down by increasing the polling
interval to 5 seconds by defaut.
This value is used in the absence of the 'polling-delay' devicetree
property.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The temperature unit is millidegree Celsius, so divide by 1000 to correctly
print the temperature values in Celsius.
While at it, also change a typo: "has beyond" to "is beyond".
Signed-off-by: Fabio Estevam <festevam@denx.de>
dev_info() message is not printed by default. Increase the log level
to dev_crit(). This allows the critical messages related to the temperature
getting beyong the alert threshold to be displayed.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
When the 'polling-delay' property is not passed via devicetree,
pdata->polling_delay keeps at 0. This causes the imx_tmu driver to get
stuck inside the busy while() loop when the CPU temperature is above
the alert point.
Fix this problem by passing a one second polling interval, which provides
a proper delay to let the system to cool down and exit the while() loop
when the temperature is below the alert point.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Select the i.MX8MM thermal driver as it is useful for displaying
the CPU temperature and its grading:
CPU: Commercial temperature grade (0C to 95C) at 38C
It also prevents booting when the temperature is above the alert
point.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Originally, exporting the ATF_LOAD_ADDR was required, but since binman has
been used to generate the flash.bin, it is no longer needed to do
such manual export.
The ATF address is now passed via binman.
Remove the unneeded export ATF_LOAD_ADDR line.
Signed-off-by: Fabio Estevam <festevam@denx.de>
To make it consistent with the instructions from other NXP imx8m boards,
such as imx8mm-evk and imx8mn-evk, use U-Boot in-tree build in the
examples.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Originally, exporting the ATF_LOAD_ADDR was required, but since binman has
been used to generate the flash.bin, it is no longer needed to do
such manual export.
The ATF address is now passed via binman in imx8mp-u-boot.dtsi:
atf {
description = "ARM Trusted Firmware";
type = "firmware";
arch = "arm64";
compression = "none";
load = <0x970000>;
entry = <0x970000>;
atf_blob: atf-blob {
filename = "bl31.bin";
type = "atf-bl31";
};
};
Remove the unneeded export ATF_LOAD_ADDR line.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Currently, a random MAC address is assigned to eth1 in Linux.
Fix this behavor by retrieving the second MAC address from the fuses.
Signed-off-by: Fabio Estevam <festevam@denx.de>
According to Documentation/devicetree/bindings/spi/spi-gpio.yaml
from Linux, the recommended spio-gpio properties are:
sck-gpios, miso-gpios and mosi-gpios.
gpio-sck, gpio-mosi and gpio-miso are considered deprecated.
Update the bindings to suggest the recommeded properties.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
According to Documentation/devicetree/bindings/spi/spi-gpio.yaml
from Linux, the recommended spio-gpio properties are:
sck-gpios, miso-gpios and mosi-gpios.
gpio-sck, gpio-mosi and gpio-miso are considered deprecated.
Currently, U-Boot only supports the deprecated properties.
Allow the soft_spi driver to support both the new and old properties.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
For changing the USB OTG node status from "okay" to "disabled" more
space is needed, so call fdt_increase_size() to avoid the following
error:
```
U-Boot 2023.07-rc5-0.0.0-devel+git.580eb31199be (Jun 27 2023 - 13:39:58 +0000)
CPU: Freescale i.MX7S rev1.2 800 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 30C
Reset cause: POR
DRAM: initcall sequence 8786eafc failed at call 8781b351 (err=-3)
### ERROR ### Please RESET the board ###
```
Ideally, fdt_status_disabled() should call fdt_increase_size() internally,
so that there would be no need for manually calling it in board code.
Do it manually for now to fix the regression.
Based on the code from board/CZ.NIC/turris_omnia/turris_omnia.c.
Reported-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Toradex Colibri iMX7S
Currently, spl_end points to the __bss_end address, which
is an external RAM address instead of the end of the SPL text
section in the internal RAM.
This causes boot failures on imx6-colibri, for example:
```
Trying to boot from MMC1
SPL: Image overlaps SPL
resetting ...
```
Fix this problem by assigning spl_end to _image_binary_end, as this
symbol properly represents the end of the SPL text section.
From u-boot-spl.map:
.end
*(.__end)
0x00000000009121a4 _image_binary_end = .
Fixes: 77aed22b48 ("spl: spl_legacy: Add extra address checks")
Reported-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de> # DH i.MX6Q DHCOM PDK2
Pass _image_binary_end to make a standard way to indicate the end
of the text section in SPL.
The motivation for this is to have a uniform way to handle
the SPL boundary checks.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Pass _image_binary_end to make a standard way to indicate the end
of the text section in SPL.
The motivation for this is to have a uniform way to handle
the SPL boundary checks.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
