Marek Vasut
057b1f8df9
The current default boot command does not respect the Linux kernel 2 MiB
alignment requirement, present on aarch64 [1]:
"
The Image must be placed text_offset bytes from a 2MB aligned base
address anywhere in usable system RAM and called there.
"
Adjust the boot command such, that it always places both Image and DT at
the nearest highest 2 MiB aligned offset. The DT is placed at lower 2 MiB
aligned address, the aarch64 Image is placed at the next higher 2 MiB
aligned address. Is is unlikely that a DT would be larger than 2 MiB on
these systems.
Replace use of hard-coded load addresses with generic ${loadaddr} aligned
using setexpr. This way, if user picks valid ${loadaddr}, their kernel and
DT address will be correctly set as well.
Fix up boot commands to use && instead of ; to exit the boot command early
in case of failure.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/arch/arm64/booting.rst#n138
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
46 lines
1.4 KiB
Plaintext
46 lines
1.4 KiB
Plaintext
#include <configs/renesas_rcar3.config>
|
|
|
|
CONFIG_ARM=y
|
|
CONFIG_ARCH_RENESAS=y
|
|
CONFIG_RCAR_GEN3=y
|
|
CONFIG_COUNTER_FREQUENCY=16666666
|
|
CONFIG_ARCH_CPU_INIT=y
|
|
CONFIG_ENV_SIZE=0x20000
|
|
CONFIG_ENV_OFFSET=0xFFFE0000
|
|
CONFIG_DEFAULT_DEVICE_TREE="renesas/r8a774a1-hihope-rzg2m-ex"
|
|
CONFIG_TARGET_HIHOPE_RZG2=y
|
|
# CONFIG_SPL is not set
|
|
CONFIG_USE_BOOTARGS=y
|
|
CONFIG_USE_BOOTCOMMAND=y
|
|
CONFIG_BOOTCOMMAND="setexpr dloadaddr ${loadaddr} + 0x200000 && setexpr dloadaddr ${dloadaddr} \\\\& 0xffc00000 && setexpr kloadaddr ${dloadaddr} + 0x200000 && tftp ${dloadaddr} Image-r8a774a1-hihope-rzg2m-ex.dtb && tftp ${kloadaddr} Image && booti ${kloadaddr} - ${dloadaddr}"
|
|
CONFIG_DEFAULT_FDT_FILE="r8a774a1-hihope-rzg2m-ex.dtb"
|
|
# CONFIG_BOARD_EARLY_INIT_F is not set
|
|
CONFIG_CMD_MMC=y
|
|
CONFIG_CMD_PART=y
|
|
CONFIG_CMD_USB=y
|
|
CONFIG_OF_LIST="renesas/r8a774a1-hihope-rzg2m-ex renesas/r8a774b1-hihope-rzg2n-ex renesas/r8a774e1-hihope-rzg2h-ex"
|
|
CONFIG_MULTI_DTB_FIT_LZO=y
|
|
CONFIG_MULTI_DTB_FIT_USER_DEFINED_AREA=y
|
|
CONFIG_ENV_IS_IN_MMC=y
|
|
CONFIG_ENV_RELOC_GD_ENV_ADDR=y
|
|
CONFIG_ENV_MMC_DEVICE_INDEX=0
|
|
CONFIG_ENV_MMC_EMMC_HW_PARTITION=2
|
|
CONFIG_GPIO_HOG=y
|
|
CONFIG_DM_PCA953X=y
|
|
CONFIG_SYS_I2C_RCAR_I2C=y
|
|
CONFIG_SYS_I2C_RCAR_IIC=y
|
|
CONFIG_MMC_IO_VOLTAGE=y
|
|
CONFIG_MMC_UHS_SUPPORT=y
|
|
CONFIG_MMC_HS400_SUPPORT=y
|
|
CONFIG_RENESAS_SDHI=y
|
|
CONFIG_SPI_FLASH_WINBOND=y
|
|
CONFIG_PHY_REALTEK=y
|
|
CONFIG_RENESAS_RAVB=y
|
|
CONFIG_TEE=y
|
|
CONFIG_OPTEE=y
|
|
CONFIG_USB=y
|
|
CONFIG_USB_XHCI_HCD=y
|
|
CONFIG_USB_EHCI_HCD=y
|
|
CONFIG_USB_EHCI_GENERIC=y
|
|
CONFIG_USB_STORAGE=y
|