Calling u_boot_console.restart_uboot() in
test_efi_selftest_watchdog_reboot() may lead to incorrect results.
While the watchdog triggered reboot is running thee test environment may
need some time before triggering a reboot itself. This may lead to
duplicate output of the U-Boot greeter which is recorded as an error.
Reported-by: Tom Rini <trini@konsulko.com>
Fixes: df172e117d ("test/py: test reboot by EFI watchdog")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Show the firmware vendor and revision to make it clear which firmware is
used, e.g. whether U-Boot is providing the boot services.
The output will look like
Firmware vendor: Das U-Boot
Firmware revision: 20241000
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add a way to factor out the CFLAGS changes for each app, since they are
all the same.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We have quite a few apps now, so create a way to specify them as a list
rather than repeating the same rules again and again.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The link rule (for $(obj)/%_efi.so) in scripts/Makefile.lib handles
pulling in efi_crt0.o and efi_reloc.o so drop the 'extra' rules.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is not actually a command so the name is confusing. Use
BOOTEFI_HELLO_COMPILE instead. Put it in the efi_loader directory
with the other such config options.
The link rule (for $(obj)/%_efi.so) in scripts/Makefile.lib handles
pulling in efi_crt0.o and efi_reloc.o so drop the 'extra' rules.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Move this section of the README into doc/ with some minor updates to
mention SPL and user lower-case hex.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
For measured be boot we must avoid any volatile values in the device-tree.
We already delete /chosen/kaslr-seed if we provide and EFI RNG protocol.
Additionally remove /chosen/rng-seed provided by QEMU or U-Boot.
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The Anbernic RG35XX series of devices are based around an Allwinner
H700 SoC with 1GB of RAM, 2 SD cards, and multiple input buttons.
This bootloader has been tested on the Anbernic RG35XX-2024 and
RG35XX-H, but should be suitable for the entire lineup of H700 based
devices.
A future series of updates will add board selection logic to identify
and load the correct device tree automatically.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Add pinctrl nodes for the r_i2c node. Without the pinmux defined the
r_i2c bus may fail to work, possibly if the bootloader uses rsb mode
for the PMIC.
Fixes: 0d17c8651188 ("arm64: dts: allwinner: Add Allwinner H616 .dtsi file")
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Fixes: 0d17c8651188 ("arm64: dts: allwinner: Add Allwinner H616 .dtsi file")
Link: https://lore.kernel.org/r/20240710231718.106894-3-macroalpha82@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[ upstream commit: 7c9ea4ab76176f65f4f55aa144f9145a4bccaacb ]
(cherry-picked from commit 1665557aa57c2140d014d68dfe1a1f92f9baac82)
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Change the Anbernic RG35XX series to use the r_i2c bus for the PMIC
instead of the r_rsb bus. This is to keep the device tree consistent
as there are at least 3 devices (the RG35XX-SP, RG28XX, and RG40XX-H)
that have an external RTC on the r_i2c bus.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Ryan Walklin <ryan@testtoast.com>
Link: https://lore.kernel.org/r/20240710231718.106894-4-macroalpha82@gmail.com
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[ upstream commit: c712e5d0985628b1df13930489b49b740e610a2b ]
(cherry picked from commit 43c3a035746af3c8cad5b65055d88f1de8406823)
Reviewed-by-by: Andre Przywara <andre.przywara@arm.com>
CSI1 channel (22) is missing and IOMMU (25) has priority flag set in
vendor bootloader. Fix that.
While at it, replace bandwidth flag with priority since original flag has
always value "true".
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
It's safer to start scanning for columns first and then rows. Columns
reside on LSB address pins, which means that second configuration will
already have all needed row pins active.
This is also preparation for introducing DDR4 support, which need scan
for banks and bank groups too.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Chris Morgan <macromorgan@hotmail.com>
When comparing configuration procedure to vendor driver, I noticed that
one command was out of order and that some delays were missing.
Fix that.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Chris Morgan <macromorgan@hotmail.com>
It seems that different dies need different PHY pin mapping. Select
alternatives at compile time.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
[adapted to switch from runtime to compile time config]
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
When trying to set the DCDC4 regulator, the code was accidentally
setting the voltage register for DCDC5 (VCC-DRAM). The higher voltage
doesn't harm the DRAM chips, but upsets the Linux regulator driver: when
it tried to correct that, it tripped over a separate DT bug.
The DCDC5 DT limits are 1.425 and 1.575V, which cannot bet set with the
rail's resolution of 50mV. The kernel driver gave up, and made in turn
the system hang, as the PMIC powers essential devices.
Fix the copy&paste bug by using the correct PMIC voltage register.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Clock gates and reset lines share a common structure in the sunxi clock
driver descriptions, but use different flags to tell them apart.
The description of the Allwinner A80 MMC clock reset lines was
erroneously using the "GATE" macro, which made the reset driver ignore
that entry, complaining with:
sunxi_set_reset: (RST-reset:#0) unhandled
Change that to the correct "RESET" macro, to make the reset driver
happy.
Fixes e0c7ce7e52 ("sunxi: clk: A80: add MMC clock support")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
With the recent "old-style sunxi" sync and the penultimate OF_UPSTREAM DT
update, both directories were based on the same v6.10 kernel tree.
And while there is one subtle difference in many Allwinner SoC's DT
files, the H616 ones turn out to be identical.
Remove the old copies of the H616 related .dts and .dtsi files, and
switch the whole H616 SoC over to use OF_UPSTREAM. This immediately
benefits from the recent upstream DT update, to kernel v6.11.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
These dependencies are required for building the drivers and create
compile errors if not enabled.
Signed-off-by: John Watts <contact@jookia.org>
[trini: Add ARCH_MVEBU to KIRKWOOD_SPI]
Signed-off-by: Tom Rini <trini@konsulko.com>
Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com> says:
This series adds support for Xilinx qspi parallel and
stacked memeories.
In parallel mode, the current implementation assumes that a maximum
of two flashes are connected. The QSPI controller splits the data
evenly between both the flashes so, both the flashes that are connected
in parallel mode should be identical.
During each operation SPI-NOR sets 0th bit for CS0 & 1st bit for CS1 in
nor->flags.
In stacked mode the current implementation assumes that a maximum of two
flashes are connected and both the flashes are of same make but can differ
in sizes. So, except the sizes all other flash parameters of both the flashes
are identical.
Spi-nor will pass on the appropriate flash select flag to low level driver,
and it will select pass all the data to that particular flash.
Write operation in parallel mode are performed in page size * 2 chunks as
each write operation results in writing both the flashes. For doubling the
address space each operation is performed at addr/2 flash offset, where addr
is the address specified by the user.
Similarly for read and erase operations it will read from both flashes, so
size and offset are divided by 2 and send to flash.
Enable the SPI_ADVANCE config option for all xilinx platforms, as
this is required for parallel-memories.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Add support for parallel memories in zynq_qspi.c driver. In case of
parallel memories STRIPE bit is set and sent to the qspi ip, which will
send data bits to both the flashes in parallel. However for few commands
we should not use stripe, instead send same data to both the flashes.
Those commands are exclueded by using zynqmp_qspi_update_stripe().
Also update copyright info for this file.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Add support for parallel memories in zynqmp_gqspi.c driver. In case of
parallel memories STRIPE bit is set and sent to the qspi ip, which will
send data bits to both the flashes in parallel. However for few commands
we should not use stripe, instead send same data to both the flashes.
Those commands are exclueded by using zynqmp_qspi_update_stripe().
Also update copyright info for this file.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Read chipselect properties from DT which are populated using 'reg'
property and save it in plat->cs[] array for later use.
Also read multi chipselect capability which is used for
parallel-memories and return errors if they are passed on using DT but
driver is not capable of handling it.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Add support for parallel memories and stacked memories configuration
in read_bar and write_bar functions.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Add support for parallel memories flash configuration in read status
register and read flag status register functions.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
In parallel mode, the current implementation assumes that a maximum of
two flashes are connected. The QSPI controller splits the data evenly
between both the flashes so, both the flashes that are connected in
parallel mode should be identical.
During each operation SPI-NOR sets 0th bit for CS0 & 1st bit for CS1 in
nor->flags.
In stacked mode the current implementation assumes that a maximum of two
flashes are connected and both the flashes are of same make but can
differ in sizes. So, except the sizes all other flash parameters of both
the flashes are identical
Spi-nor will pass on the appropriate flash select flag to low level
driver, and it will select pass all the data to that particular flash.
Write operation in parallel mode are performed in page size * 2 chunks as
each write operation results in writing both the flashes. For doubling
the address space each operation is performed at addr/2 flash offset,
where addr is the address specified by the user.
Similarly for read and erase operations it will read from both flashes,
so size and offset are divided by 2 and send to flash.
Adding the config option SPI_ADVANCE for non SPL code.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
By default flash lock option is enabled, enable this option only
when it is required. By disabling the lock config will save some
amount of memory.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
During DT sync with kernel 6.6, AVS feature was removed by mistake.
So adding back AVS feature.
Fixes: df73e791ce09("arm: dts: j7200: dts sync with Linux 6.6-rc1")
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
There are lots of usecases for running baremetal ELF
binaries via bootelf but if you enable bootelf you
get bootvx as well and you probably don't want or need
it.
Hide bootvx behind it's own configuration option.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Add the "required", "algo", and "key-name-hint" nodes to the
signature/key node if ecdsa256 is used.
This change is mainly copy&paste from rsa_add_verify_data which already
adds these nodes.
Signed-off-by: Matthias Pritschet <matthias.pritschet@itk-engineering.de>
If the signature/key node(s) are not yet present in the U-Boot device
tree, ecdsa_add_verify_data simply fails if it can't find the nodes.
This behaviour differs from rsa_add_verify_data, wich does add the missing
nodes and proceeds in that case.
This change is mainly copy&paste from rsa_add_verify_data to add the
same behaviour to ecdsa_add_verify_data.
Signed-off-by: Matthias Pritschet <matthias.pritschet@itk-engineering.de>
There is no need to define a default for bootcmd in R5 u-boot because
the R5 is directly booting into the next stage A53 bootloader.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Initializing a clock driver to read a known static clock rate can take
some time at U-Boot proper pre-reloc phase.
Change to first try and read clock rate from DT to speed up boot time,
fall back to getting the clock rate from clock driver.
This help reduce boot time by around:
- ~35ms on a Radxa ROCK Pi 4 (RK3399)
- ~15ms on a Radxa ZERO 3W (RK3566)
Time that is wasted getting a static rate known at compile time.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Mediatek pinctrl drivers call mtk_gpiochip_register() to bind the child
gpio controller as part of mtk_pinctrl_common_probe(). This breaks
gpiohog support because the gpio controller is bound too late for
DM_FLAG_PROBE_AFTER_BIND (set while binding hogs) to work.
Move the mtk_gpiochip_register() to mtk_pinctrl_common_bind() and call
this as the .bind method of each of the mediatek pinctrl drivers.
Signed-off-by: Chris Webb <chris@arachsys.com>
The SSCG is active with MDSEL[12] is not set. Previous commit
99c7e03119 ("clk: renesas: rcar-gen3: Replace SSCG caching
with MDSEL/PE caching") inverted the conditional assignment
of priv->sscg = !(cpg_mode & BIT(12)) during conversion from
(priv->sscg ? 16 : 0) to priv->cpg_mode & BIT(core->offset) ? 16 : 0;
Invert the assignment back to the correct state.
This fixes R8A77980, R8A77990, R8A77995 and R8A774C0.
Fixes: 99c7e03119 ("clk: renesas: rcar-gen3: Replace SSCG caching with MDSEL/PE caching")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
These are a number of assorted upstream Linux fixes to the
BRCMNAND driver.
This patch set lowers the hamming distance between the Linux
and U-Boot drivers a bit as well, while we deviate quite
a bit it is still possible to bring fixes over thanks to
exercises like this.
The patches pass the pipeline CI:
https://source.denx.de/u-boot/custodians/u-boot-nand-flash/-/pipelines/22535
Heinrich SchuchardtandTom Rini
Simon GlassandTom Rini
Chris MorganandAndre Przywara
Jernej SkrabecandAndre Przywara
John WattsandTom Rini
Venkatesh Yadav AbbarapuandTom Rini
Ashok Reddy SomaandTom Rini
Udit KumarandTom Rini
Daniel PalmerandTom Rini
Matthias PritschetandTom Rini
Wadim EgorovandTom Rini
Jonas KarlmanandTom Rini
Chris WebbandTom Rini
Marek VasutandTom Rini