Just check that the length is at least 2. This allows passing strings
like ".b", which can be convenient when constructing
tests (i.e. parametrizing the suffix used).
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
This function obviously does not and must not modify "arg". Change the
prototype to allow passing an argument of type "const char*" without
requiring a cast.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Now that the cp command is changed to use memmove() internally, update
the documentation to explicitly state that overlapping regions are
allowed.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
There's no 'mv' shell command for handling overlapping src and dst
regions, and there's no point introducing one, when we can just make
the existing 'cp' command DTRT in all cases. memmove() should at most
be a few instructions more then memcpy() (to detect the appropriate
direction to do the copy), which is of course completely in the noise
with all the string processing that a shell command does.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Add the following memory tests:
memtest_negative - To test mtest command by providing incorrect inputs
memtest_ddr - To test memory write-read-comparision for DDR memory
Signed-off-by: Love Kumar <love.kumar@amd.com>
Add reset controller driver for Nuvoton BMCs.
The npcm reset driver not only supports reset each module reset
but setting initial value of reset Control Registers.
And The driver support each module reset.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Add below test cases for i2c commands:
i2c_bus - To show i2c bus info,
i2c_dev - To set or show the current bus,
i2c_probe - To probe the i2c device,
i2c_eeprom - To test i2c eeprom device,
i2c_probe_all_buses - To list down all the buses and probes it
Signed-off-by: Love Kumar <love.kumar@amd.com>
Add below test cases for mii commands:
mii_info -To display MII PHY info
mii_list - To list MII devices
mii_set_device - To set MII device
mii_read - To reads register from MII PHY address
mii_dump - To display data from MII PHY address
Signed-off-by: Love Kumar <love.kumar@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add pe2201 platform code and the device tree of pe2201 platform board.
The initial support comprises the UART and PCIe.
Signed-off-by: TracyMg_Li <TracyMg_Li@outlook.com>
Changes since v1:
fix space corrupt.
Changes since v2:
switch to bootstd and text environment.
Changes since v3:
add environment variables.
next_header() and get_next_header() only differ in how the const attribute
is used. One function taking a const parameter and returning a non-const is
good enough.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
QEMU provides SMBIOS tables with detailed information. We should not try to
replicate them in U-Boot.
If we want to inform about U-Boot, we can add a Firmware Inventory
Information (type 45) table in future.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for J721E HS-SE 2.0 device. Make use of the existing
templates and override the phandles for sysfw.itb so that builds do not
fail.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Add below test cases for mdio commands:
mdio_list - To list MDIO buses
mdio_read - To read PHY's register at <devad>.<reg>
mdio_write - To write PHY's register at <devad>.<reg>
Signed-off-by: Love Kumar <love.kumar@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Abort the dhcp request in the middle by pressing ctrl + c on u-boot
prompt and validate the abort status.
Signed-off-by: Love Kumar <love.kumar@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Qualcomm architecture changes:
* Move clock and pinctrl drivers out of mach-snapdragon
* Various clock driver improvements
* Convert PMIC power/reset key driver to use the button API
* Preparetory work for migrating to upstream DT
sandbox_flattree enables QCOM_PMIC_GPIO which now depends on BUTTON. As
a result the button tests now get run, but fail because the ADC and GPIO
button drivers aren't enabled.
Enable them to run the tests for sandbox_flattree.
Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
With the recent changes to the Qualcomm PMIC GPIO driver the sandbox
tests for it no longer pass, update the DTS and tests to work with the
changes.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Linux DTs stuff a value indicating if the USID is a USID or a GSID in the
reg property, the Linux SPMI driver then reads the two address cells
separately. U-boot's dev_read_addr() doesn't know how to handle this, so
use ofnode_read_u32_index() to get just the USID.
The Qcom pmic driver doesn't have support for GSID handling, so just
ignore the second value for now.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The core and chnl register ranges were swapped on SDM845. Fix it, and
fetch the register ranges by name instead of by index.
Drop the cosmetic "version" variable and clean up the debug logging.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Upstream uses the gpio-ranges property to define the number of GPIOs,
support for parsing this when gpio-count is unspecified
Additionally, drop the bank-name property as it isn't used in upstream,
and we can just hardcode the bank name instead.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The PMIC button driver is a much better representation of the hardware
here, adjust the boards to use upstream DT and the PMIC button driver
instead of exposing the buttons as GPIOs and relying on the GPIO-button
driver.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Qualcomm PMICs include a "pon" function which handles two buttons, the
power button and "resin" button (usually volume down). Introduce a new
driver following upstream Linux DT to enable these and map them to Enter
and Down respectively to enable use in boot menus.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
priv->pid is uint32_t, but dev_read_addr() returns a uint64_t on arm64,
with the upper bits being used for error codes. Do error checking before
downcasting to u32 to prevent errors being silently ignored.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
devm_clk_get() returns an ERR_PTR on failure, not null. Fix the check to
avoid the board crashing when the clock isn't available.
Additionally, add the missing error handling for this function.
Fixes: 324df15a29 ("serial: qcom: add support for GENI serial driver")
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
commit 1b15483deb ("misc: add Qualcomm GENI SE QUP device driver")
introduced support for platform-specific oversampling values, necessary
to configure the UART clocks on all platforms at runtime. However it
relies in probing a parent device. Despite the DM_FLAG_PRE_RELOC flag,
this is not done consistently during boot.
Instead, take another approach by relying on ofnode_ helpers to read the
serial engine base address and do the read directly. This fixes early
UART on boards with a non-default oversampling rate.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The pinctrl and GPIO drivers are currently heavily incompatible with
upstream. Most Qualcomm pinctrl blocks feature "tiles" of pins, each at
it's own address. Introduce support for these by allowing the soc driver
to specify per-pin register offsets similarly to the Linux driver.
Adjust the GPIO driver to handle these too, and finally enable support
for all pins with the same numbering as used in Linux.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Drop the duplicated pinctrl-snapdragon driver from mach-ipq40xx and add
it to drivers/pinctrl/qcom.
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Move the Qualcomm pinctrl drivers out of mach-snapdragon and over to the
rest of the pinctrl drivers, adjust the drivers so that support for each
platform can be enabled/disabled individually and introduce platform
specific configuration options.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
The RCG divider field takes a value of (2*h - 1) where h is the divisor.
This allows fractional dividers to be supported by calculating them at
compile time using a macro.
However, the clk_rcg_set_rate_mnd() function was also performing the
calculation. Clean this all up and consistently use the F() macro to
calculate these at compile time and properly support fractional divisors.
Additionally, improve clk_bcr_update() to timeout with a warning rather
than hanging the board, and make the freq_tbl struct and helpers common
so that they can be reused by future platforms.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
This property is needed on some platforms to ensure that only the
relevant bits are set in the M/N/D registers.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Currently, it isn't possible to build clock drivers for more than one
platform due to how the msm_enable() and msm_set_rate() callbacks are
implemented.
Extend qcom_clk_data to include function pointers for these and convert
all platforms to use them.
Previously, clock drivers relied on include/configs/<board.h> to include the
board specific sysmap header, however as most of the header contents are clock
driver related, import the contents directly into each clock driver and
remove the header. The only exception here is the dragonboard820c board file
which includes some pinctrl macros, those are also inlined.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
[caleb: remove additional sysmap-sdm845.h mention]
Many gate clocks can be enabled with a single register write, add support
for defining these simple gate clocks and add the ones found on SDM845.
While we're here, inline clk_init_uart() into msm_set_rate().
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Qualcomm's clock controller blocks actually do much more than it
says on the tin.. They provide clocks, resets and power domains.
Currently, U-Boot requires one to spawn 2 separate devices for
controlling clocks and resets, both spanning the same register space.
Refactor the code to make it work with just a single DT node, making
it compatible with upstream Linux bindings and dropping the dedicated
reset driver in favour of including it in the clock driver.
Heavily inspired by Renesas code for a similar hw block.
[caleb: moved drivers to clk/qcom, added reset driver and adjusted bind
logic. Imported qcom,gcc-ipq4019.h from Linux]
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
This driver is just a stub, but it's necessary to support the upcoming
reset driver changes.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Clock drivers don't belong here, move them to the right place and
declutter mach-snapdragon a bit.
To de-couple these drivers from specific "target" platforms, add
additional config options to enable each clock driver gated behind a
common CLK_QCOM option and enable them by default for the respective
targets. This will make future work easier as we move towards a generic
Qualcomm target.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Pull request for u-boot-nand-20240115
The first patch is by Heinrich Schuchardt and fixes an integer overflow
The following two patches are by Dario Binacchi and add arguments check
to the nand_mtd_to_devnum() and nand_register() functions.
The remaining patches are by Roger Quadros and include various fixes for
the OMAP platform.
We load two boot image source descriptor structures from last
two sectors in the SPI NOR flash and determine the boot source
for loading the kernel/DTB images, then adjust the boot order for
loading image from eMMC boot0 or boot1 partition.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Oliver FasoandHeinrich Schuchardt
Mattijs KorpershoekandHeinrich Schuchardt
Venkatesh Yadav AbbarapuandMichal Simek
Rasmus VillemoesandTom Rini
Love KumarandTom Rini
Jim LiuandTom Rini
TracyMg_LiandTom Rini
Heinrich SchuchardtandTom Rini
Neha Malcom FrancisandTom Rini
Wadim EgorovandTom Rini
Caleb Connolly
Konrad DybcioandCaleb Connolly
Anatolij GustschinandFabio Estevam